QEB75-48S15 参数 Datasheet PDF下载

Model

Number

QEB75-24S3P3

QEB75-24S05

QEB75-24S12

QEB75-24S15

QEB75-48S1P8

QEB75-48S2P5

QEB75-48S3P3

QEB75-48S05

QEB75-48S12

QEB75-48S15

Input

Range

18 – 36 VDC

18 – 36 VDC

18 – 36 VDC

18 – 36 VDC

36 – 75 VDC

36 – 75 VDC

36 – 75 VDC

36 – 75 VDC

36 – 75 VDC

36 – 75 VDC

(4)

(4)

Input Current

Output Current

Load

Output

Output

Eff

(3)

(2)

(%) regulation

Voltage Min. load Full load Ripple & Noise No load

Full load

3.3 VDC

5 VDC

12 VDC

15 VDC

1.8 VDC

2.5 VDC

3.3 VDC

5 VDC

12 VDC

15 VDC

0mA

0mA

0mA

0mA

0mA

0mA

0mA

0mA

0mA

0mA

20A

15A

6.25A

5A

25A

25A

20A

15A

6.25A

5A

100mVp-p

100mVp-p

100mVp-p

100mVp-p

100mVp-p

100mVp-p

100mVp-p

100mVp-p

100mVp-p

100mVp-p

80mA

130mA

190mA

190mA

50mA

50mA

70mA

80mA

130mA

130mA

3198mA

3634mA

3662mA

3634mA

1157mA

1569mA

1599mA

1817mA

1831mA

1817mA

89

90

90

90

85

87

90

90

90

90

10mV

15mV

36mV

45mV

5.4mV

7.5mV

10mV

15mV

36mV

45mV

Note :

1.BELLCORE TR-NWT-000332. Case 1: 80% Stress, Temperature at 40ºC.

MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load(Ground, Benign, controlled environment)

2.Maximum value at nominal input voltage and full load of standard type.

3.Typical value at nominal input voltage and no load.

4.Typical value at nominal input voltage and full load.

5.Maximum output deviation is 10% inclusive of trim. If remote sense is not being used, the + sense should be connected to its corresponding

+OUTPUT and likewise the –sense should be connected to its corresponding –OUTPUT.

6.The positive logic and pin length are optional ( see table ). The pin voltage is referenced to –Vin.

7.Heat sink is optional and P/N：7G-0029A-F, 7G-0030A-F, 7G-0031A-F, 7G-0032A-F.

8.The QEB75 meets EN55022 class A and class B only with external components connected before the input pin to the converter.

9.An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5.

The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220μF/100V, ESR 48mΩ.

10.BASEPLATE GROUNDING：Base-plate should be grounded at one of the four screw bolts prior to operation.

11.The converter is provided by basic insulation.

Page 2 of 4 Issued Date：2008/05/21