欢迎访问ic37.com |
会员登录 免费注册
发布采购

4230-51 参数 Datasheet PDF下载

4230-51图片预览
型号: 4230-51
PDF下载: 下载PDF文件 查看货源
内容描述: SPDT大功率UltraCMOS⑩ RF开关 [SPDT High Power UltraCMOS⑩ RF Switch]
分类和应用: 开关光电二极管
文件页数/大小: 7 页 / 258 K
品牌: PEREGRINE [ PEREGRINE SEMICONDUCTOR CORP. ]
 浏览型号4230-51的Datasheet PDF文件第2页浏览型号4230-51的Datasheet PDF文件第3页浏览型号4230-51的Datasheet PDF文件第4页浏览型号4230-51的Datasheet PDF文件第5页浏览型号4230-51的Datasheet PDF文件第6页浏览型号4230-51的Datasheet PDF文件第7页  
Product Specification
PE4230
Product Description
The PE4230 UltraCMOS™ RF Switch is designed to cover a
broad range of applications from DC through 3000 MHz. This
single-supply reflective switch integrates on-board CMOS
control logic driven by a simple, single-pin CMOS or TTL
compatible control input. Using a nominal +3-volt power supply,
a typical input 1 dB compression point of +32 dBm can be
achieved. The PE4230 also exhibits input-output isolation of
better than 39 dB at 1000 MHz and is offered in a small 8-lead
MSOP package.
The PE4230 SPDT High Power UltraCMOS™ RF Switch is
manufactured in Peregrine’s patented Ultra Thin Silicon
(UTSi®) CMOS process, offering the performance of GaAs with
the economy and integration of conventional CMOS.
Figure 1. Functional Diagram
RFC
SPDT High Power UltraCMOS™
RF Switch
Features
Single 3-volt power supply
Low insertion loss: 0.35 dB at
1000 MHz, 0.55 dB at 2000 MHz
High isolation of 39 dB at 1000 MHz,
30 dB at 2000 MHz
Typical input 1 dB compression point
of +32 dBm
Single-pin CMOS or TTL logic control
Low cost
Figure 2. Package Type
8-lead MSOP
RF1
RF2
CMOS
Control
Driver
CTRL
Table 1. Electrical Specifications @ +25 °C, V
DD
= 3 V
(Z
S
= Z
L
= 50
)
Parameter
Operation Frequency
1
Insertion Loss
Isolation – RFC to RF1/RF2
Isolation – RF1 to RF2
Return Loss
‘ON’ Switching Time
‘OFF’ Switching Time
Video Feedthrough
2
Input 1 dB Compression
Input IP3
2000 MHz
2000 MHz, 17 dBm
30
50
1000 MHz
2000 MHz
1000 MHz
2000 MHz
1000 MHz
2000 MHz
1000 MHz
2000 MHz
CTRL to 0.1 dB final value, 2 GHz
CTRL to 25 dB isolation, 2 GHz
38
28
33.5
26.5
23.5
14.5
Conditions
Minimum
DC
Typical
0.35
0.55
39
30
35
28
25.5
15.4
200
90
15
32
Maximum
3000
0.45
0.65
Units
MHz
dB
dB
dB
dB
dB
dB
dB
dB
ns
ns
mV
pp
dBm
dBm
Notes: 1. Device linearity will begin to degrade below 10 MHz.
2. The DC transient at the output of any port of the switch when the control voltage is switched from Low to
High or High to Low in a 50
test set-up, measured with 1ns risetime pulses and 500 MHz bandwidth.
Document No. 70-0029-02
www.psemi.com
©2005 Peregrine Semiconductor Corp. All rights reserved.
Page 1 of 7