PE94302
Advance Information
Figure 3. Pin Configuration (Top View)
26
GND
25
GND
24
GND
28
C0.5
27
C1
23
C2
22
C4
Table 3. Absolute Maximum Ratings
Symbol
V
DD
Parameter/Conditions
Power supply voltage
Negative Power supply
voltage (-V
DD
)
Voltage on any DC input
Storage temperature range
Input power (50Ω)
ESD voltage (Human Body
Model)
Min
-0.3
-4.0
-0.3
-65
Max
4.0
0.3
V
DD
+
0.3
150
24
500
Units
V
V
V
°C
dBm
V
C16
GND
RF1
GND
Data
GND
CLK
1
2
3
4
5
6
7
21
20
C8
GND
V
ss
V
I
T
ST
P
IN
V
ESD
19
RF2
PE94302
18
17
16
GND
P/S
GND
15
Reset
Table 2. Pin Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Paddle
Absolute Maximum Ratings are those values listed in
the above table. Exceeding these values may cause
permanent device damage. Functional operation
should be restricted to the limits in the DC Electrical
Specifications table. Exposure to absolute maximum
ratings for extended periods may affect device
reliability.
GND
10
11
GND
12
13
RS2
RS1
V
DD
Pin Name
C16
GND
RF1
GND
Data
GND
CLK
LE
V
DD
GND
RS1
GND
RS2
V
SS
Reset
GND
P/S
GND
RF2
GND
C8
C4
C2
GND
GND
GND
C1
C0.5
GND
Description
Attenuation control bit, 16dB
Ground connection
RF port (Note 1).
Ground connection
Serial interface data input
Ground connection
Serial interface clock input.
Latch Enable input (Note 2).
Power supply pin.
Ground connection
Reset Selection (note 3)
Ground connection
Reset Selection (Note 3)
Negative supply voltage
Reset (Note 4)
Ground connection
Parallel/Serial mode select.
Ground connection
RF port (Note 1).
Ground connection
Attenuation control bit, 8 dB.
Attenuation control bit, 4 dB.
Attenuation control bit, 2 dB.
Ground connection
Ground connection
Ground connection
Attenuation control bit, 1 dB.
Attenuation control bit, 0.5 dB.
Ground connection
V
SS
LE
14
8
9
Table 4. DC Electrical Specifications
Parameter
V
DD
Power Supply Voltage
V
ss
Power Supply Voltage
I
DD
Power Supply Current
I
ss
Power Supply Current
T
OP
Operating temperature
range
Digital Input High
Digital Input Low
Digital Input Leakage
-100
-40
0.7xV
DD
0.3xV
DD
1
85
Min
2.7
-3.3
Typ
3.0
-3.0
Max
3.3
-2.7
100
Units
V
V
µA
µA
°C
V
V
µA
Exposed Solder Pad Connection
The exposed solder pad on the bottom of the package
must be grounded for proper device operation.
Electrostatic Discharge (ESD) Precautions
When handling this UltraCMOS™ device, observe the
same precautions that you would use with other ESD-
sensitive devices. Although this device contains
circuitry to protect it from damage due to ESD,
precautions should be taken to avoid exceeding the
rate specified in Table 3.
Latch-Up Avoidance
Unlike conventional CMOS devices, UltraCMOS™
devices are immune to latch-up.
Note 1: Both RF ports must be held at 0 V
DC
or DC blocked with an
external series capacitor.
2: Latch Enable (LE) has an internal 100 kΩresistor to V
DD.
3: Must be tied to Vdd or GND under normal operation.
4: Must be tied to GND under normal operation
©2005-2007 Peregrine Semiconductor Corp. All rights reserved.
Page 2 of 6
Switching Frequency
The PE94302 has a maximum 25 kHz switching rate.
Document No. 70/0186-02
│
UltraCMOS™ RFIC Solutions
PEREGRINE [ PEREGRINE SEMICONDUCTOR CORP. ]
