21098765432121098765432109876543210987654321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321
21098765432121098765432109876543210987654321210987654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321
PI3B3384, PI3B32384(25Ω)
Ω
3.3V, 10-Bit, 2-Port NanoSwitch
Power Supply Characteristics
Parameters Description
I
CC
∆I
CC
Quiescent Power
Supply Current
Supply Current per
Input @ TTL HIGH
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device.
2. Typical values are at V
CC
= 3.3V, +25°C ambient.
3. Per TTL driven input (control inputs only); A and B pins do not contribute to I
CC
.
Test Conditions
(1)
V
CC
= Max.,
V
IN
= GND or V
CC
V
CC
= Max., V
IN
= 3.0V
(3)
PI3B3384
PI3B32384
Min.
—
—
Typ
(2)
0.1
—
Max.
3
750
Units
µA
µA
PI3B3384 Switching Characteristics Over Operating Range
PI3B3384
Parame te rs
De s cription
Conditions
(
3)
M in.
t
PLH
t
PHL
t
PZH
t
PZL
t
PHZ
t
PLZ
Propagation Delay
(2,3)
Ax to Bx, Bx to Ax
Bus Enable Time
BEx to Ax or Bx
Bus Disable Time
BEx to Ax or Bx
C
L
= 50pF
R
L
= 500
Ω
C
L
= 50pF
R
L
= 500
Ω
R
L
= 500
Ω
1. 0
1. 0
Com.
M a x.
0.25
4.0
3.5
ns
Units
Notes:
1. See test circuit and waveforms.
2. This parameter is guaranteed but not tested on Propagation Delays.
3. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time
constant for the switch alone is of the order of 0.25ns for 50pF load. Since this time constant is much smaller than the rise/fall times of typical driving
signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving
circuit on the driving side of the switch and its interaction with the load on the driven side.
PI3B32384 Switching Characteristics over Operating Range
PI3B32384
Com.
Min.
Max.
0.25
1.0
1.0
4.0
4.5
ns
Parameters Description
t
PLH
t
PHL
t
PZH
t
PZL
t
PHZ
t
PLZ
Propagation Delay
(2,3)
Ax to Bx, Bx to Ax
Bus Enable Time
BE
X
to Ax or Bx
Bus Disable Time
BEx to Ax or Bx
Conditions
(1)
C
L
= 50pF
R
L
= 500Ω
C
L
= 50pF,
R
L
= 500Ω,
R
L
= 500Ω
Units
Notes:
1. See test circuit and waveforms.
2. This parameter is guaranteed but not tested on Propagation Delays.
3. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time
constant for the switch alone is of the order of 0.25ns for 50pF load. Since this time constant is much smaller than the rise/fall times of typical driving
signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving
circuit on the driving side of the switch and its interaction with the load on the driven side.
3
PS8161F
09/23/04
PERICOM [ PERICOM SEMICONDUCTOR CORPORATION ]
