BP1042 70 MHz SAW Filter
•
•
•
•
•
Designed for CDMA Receiver IF Applications
Simple External Impedance Matching
Hermetic Metal DIP
Unbalanced Input and Output
Complies with Directive 2002/95/EC (RoHS)
Pb
See Associated Plots
Characteristic
Nominal Center Frequency
Passband
Insertion Loss at fc
1 dB Passband
3 dB Passband
Group Delay Variation over fc
±550
kHz
Phase Linearity over fc
±550
kHz
Rejection
At fc
±1.0
MHz
Ultimate from 1 MHz to 105 MHz
Operating Temperature Range
Impedance Matching to 50
Ω
unbalanced
Suggested Matching Network Impedance at Port 1
Suggested Matching Network Impedance at Port 2
Case Style
Lid Symbolization (RR = run code, LL = lot code)
Sym
fc
IL
BW
1
BW
3
GDV
Min
±455
±550
T
A
40
40
-25
Typ
70.000
22
±500
±600
150
4
45
50
Max
28
Units
MHz
dB
kHz
ns
P-P
°
P-P
dB
°C
Notes
1
1, 2
175
5
1, 2, 3
1
+85
External L-C
375 nH in parallel with 310
Ω
240 nH in parallel with 320
Ω
DIP14L-8 22.1 x 12.6 mm Nominal Footprint
RFM BP1042 RRLL
Electrical Connections
(See note 3)
Connection Terminals
Port 1 Hot 7
Port 1 Gnd Return 9
Port 2 Hot 14
Port 2 Gnd Return 2
No Connection 1, 8
Case Ground 2, 9 & All others
Absolute Maximum Ratings
Rating
Value
Units
Maximum Incident Power in Passband
+10
dBm
Max. DC voltage between any 2 terminals
30
VDC
Storage Temperature Range
-40 to +85
°C
Max Soldering Temperature
260°C for 30 s
Suitable for lead-free Soldering
Notes:
1. Unless noted otherwise, all specifications apply
over the operating temperature range
with filter soldered to the specified
demonstration board with impedance matching to 50
Ω
and measured with 50
Ω
network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is
dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. All “NC” or “no
connection pins should be grounded.
4. “LRIP” or “L” after the part number indicates “low rate initial production” and “ENG” or “E” indicates “engineering prototypes.”
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching
may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
9.
©Copyright
1999, RF Monolithics Inc.
10. Electrostatic Sensitive Device. Observe precautions for handling.
RF Monolithics, Inc.
4441 Sigma Road
Dallas, Texas 75244
USA
Phone: +1(972)233-2903
Fax: +1(972)387-8148
e-mail:
info@rfm.com
Home page:
www.rfm.com
European Sales Office
44 1963 251383
44 1963 251510
BP1042.DOC 11/22/04 D
RFM [ RF MONOLITHICS, INC ]
