Pin
Name
Description
This pin is the receiver low-pass filter bandwidth adjust. The filter bandwidth is set by a resistor R
LPF
between this pin and
ground. The resistor value can range from 330 K to 820 ohms, providing a filter 3 dB bandwidth f
LPF
from 4.5 kHz to 1.8
MHz. The resistor value is determined by:
R
LPF
= 1445/ f
LPF
, where R
LPF
is in kilohms, and f
LPF
is in kHz
A ±5% resistor should be used to set the filter bandwidth. This will provide a 3 dB filter bandwidth between f
LPF
and 1.3*
f
LPF
with variations in supply voltage, temperature, etc. The filter provides a three-pole, 0.05 degree equiripple phase
response. The peak drive current available from RXDATA increases in proportion to the filter bandwidth setting.
GND2 is an IC ground pin. It should be connected to GND1 by a short, low inductance trace.
RREF is the external reference resistor pin. A 100 K reference resistor is connected between this pin and ground. A ±1%
resistor tolerance is recommended. It is important to keep the total capacitance between ground, Vcc and this node to less
than 5 pF to maintain current source stability. If THLD1 and/or THDL2 are connected to RREF through resistor values less
that 1.5 K, their node capacitance must be added to the RREF node capacitance and the total should not exceed 5 pF.
THLD2 is the “dB-below-peak” data slicer (DS2) threshold adjust pin. The threshold is set by a 0 to 200 K resistor R
TH2
between this pin and RREF. Increasing the value of the resistor decreases the threshold below the peak detector value
(increases difference) from 0 to 120 mV. For most applications, this threshold should be set at 6 dB below peak, or 60 mV
for a 50%-50% RF amplifier duty cycle. The value of the THLD2 resistor is given by:
R
TH2
= 1.67*V, where R
TH2
is in kilohms and the threshold V is in mV
A ±1% resistor tolerance is recommended for the THLD2 resistor. Leaving the THLD2 pin open disables the dB-below-
peak data slicer operation.
The THLD1 pin sets the threshold for the standard data slicer (DS1) through a resistor R
TH1
to RREF. The threshold is
increased by increasing the resistor value. Connecting this pin directly to RREF provides zero threshold. The value of the
resistor depends on whether THLD2 is used. For the case that THLD2 is not used, the acceptable range for the resistor is
0 to 100 K, providing a THLD1 range of 0 to 90 mV. The resistor value is given by:
R
TH1
= 1.11*V, where R
TH1
is in kilohms and the threshold V is in mV
For the case that THLD2 is used, the acceptable range for the THLD1 resistor is 0 to 200 K, again providing a THLD1
range of 0 to 90 mV. The resistor value is given by:
R
TH1
= 2.22*V, where R
TH1
is in kilohms and the threshold V is in mV
A ±1% resistor tolerance is recommended for the THLD1 resistor. Note that a non-zero DS1 threshold is required for
proper AGC operation.
The interval between the falling edge of an ON pulse to the first RF amplifier and the rising edge of the next ON pulse to
the first RF amplifier t
PRI
is set by a resistor R
PR
between this pin and ground. The interval t
PRI
can be adjusted between
0.1 and 5 µs with a resistor in the range of 51 K to 2000 K. The value of R
PR
is given by:
R
PR
= 404* t
PRI
+ 10.5, where t
PRI
is in µs, and R
PR
is in kilohms
A ±5% resistor value is recommended. When the PWIDTH pin is connected to Vcc through a 1 M resistor, the RF amplifi-
ers operate at a nominal 50%-50% duty cycle, facilitating high data rate operation. In this case, the period t
PRC
from start-
to-start of ON pulses to the first RF amplifier is controlled by the PRATE resistor over a range of 0.1 to 1.1 µs using a resis-
tor of 11 K to 220 K. In this case the value of R
PR
is given by:
R
PR
= 198* t
PRC
- 8.51, where t
PRC
is in µs and R
PR
is in kilohms
A ±5% resistor value should also be used in this case. Please refer to the
ASH Transceiver Designer’s Guide
for additional
amplifier duty cycle information. It is important to keep the total capacitance between ground, Vcc and this pin to less than
5 pF to maintain stability.
The PWIDTH pin sets the width of the ON pulse to the first RF amplifier t
PW1
with a resistor R
PW
to ground (the ON pulse
width to the second RF amplifier t
PW2
is set at 1.1 times the pulse width to the first RF amplifier). The ON pulse width t
PW1
can be adjusted between 0.55 and 1 µs with a resistor value in the range of 200 K to 390 K. The value of R
PW
is given by:
R
PW
= 404* t
PW1
- 18.6, where t
PW1
is in µs and R
PW
is in kilohms
A ±5% resistor value is recommended. When this pin is connected to Vcc through a 1 M resistor, the RF amplifiers operate
at a nominal 50%-50% duty cycle, facilitating high data rate operation. In this case, the RF amplifier ON times are con-
trolled by the PRATE resistor as described above. It is important to keep the total capacitance between ground, Vcc and
this node to less than 5 pF to maintain stability. When using the high data rate operation with the sleep mode, connect the
1 M resistor between this pin and CNTRL1 (Pin 17), so this pin is low in the sleep mode.
VCC2 is the positive supply voltage pin for the receiver RF section. This pin must be bypassed with an RF capacitor, which
may be shared with VCC1. VCC2 must also be bypassed with a 1 to 10 µF tantalum or electrolytic capacitor.
9
LPFADJ
10
GND2
11
RREF
12
THLD2
13
THLD1
14
PRATE
15
PWIDTH
16
VCC2
RF Monolithics, Inc.
Phone: (972) 233-2903
Fax: (972) 387-8148
RFM Europe
Phone: 44 1963 251383
Fax: 44 1963 251510
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
E-mail: info@rfm.com
http://www.rfm.com
RX6000-062905
Page 9 of 10
RFM [ RF MONOLITHICS, INC ]
