Preliminary
®
SF2030A
243.95 MHz
Pb
Value
-15 to +80
-40 to +85
30
+15
Units
°C
°C
V
dBm
•
•
•
•
Designed for PHS BTS IF Applications
Excellent Size-to Performance Ratio
Hermetic 11.5 X 4.0 mm Surface-Mount Case
Complies with Directive 2002/95/EC (RoHS)
SAW Filter
Maximum Ratings
Rating
Operating Temperature Range
Storage Temperature Range
Maximum DC Voltage
Maximum Source Power
Maximum Soldering Profile
260°C for 30sec
SM1154-14
Electrical Characteristics
Characteristic
Nominal Frequency
Nominal Insertion Attenuation
Pass band width at 3 dB (Relative to Fn)
Point of left side
Point of right side
Amplitude Ripple (peak-valley)
FN - 110 kHz ---- Fn + 110kHz
Group Delay Ripple
FN - 110 kHz ---- Fn + 110kHz
Relative Attenuation (Relative to Fn)
Fn - 21.6 MHz
Fn - 21.4 MHz
Fn - 10.8 MHz
Fn - 1.2 MHz
Fn - 0.7 MHz
Fn - 0.6 MHz
Fn - 0.5 MHz
Fn + 0.5 MHz
Fn + 0.6 MHz
Fn + 0.7 MHz
Fn + 1.2 MHz
Fn + 10.8 MHz
Lid Symbolization (YY=year, WW=week, S=shift) See note 4
Sym
f
N
B
3dB
-150
+150
0.6
1.0
0.5
60
60
55
30
30
30
15
15
30
30
30
55
RFM SF2030A YYWWS
dB
µsec
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
kHz
Notes
Min
Typ
243.95
Max
5
Units
MHz
dB
Notes:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to
50
Ω
and measured with 50
Ω
network analyzer.
Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance
matching design. See Application Note No. 42 for details.
"LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
The design, manufacturing process, and specifications of this filter are subject to change.
Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that
the filter must always be installed in one direction per the circuit design.
US and international patents may apply.
RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
©Copyright 1999, RF Monolithics Inc.
Electrostatic Sensitive Device. Observe precautions for handling.
RF Monolithics, Inc.
Phone: (972) 233-2903
Fax: (972) 387-8148
RFM Europe
Phone: 44 1963 251383
Fax: 44 1963 251510
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
E-mail: info@rfm.com
http://www.rfm.com
SF2030A-10/25/07
Page 1
RFM [ RF MONOLITHICS, INC ]
