RT9013
Applications Information
Preliminary
Enable
The RT9013 goes into sleep mode when the EN pin is in a
logic low condition. During this condition,
the RT9013 has
an EN pin to turn on or turn off regulator, When the EN pin
is logic hight, the regulator will be turned on. The supply
current to 0.7μA typical. The EN pin may
be directly tied
to V
IN
to keep the part on. The Enable input is CMOS
logic and cannot be left floating.
PSRR
The power supply rejection ratio (PSRR) is defined as the
gain from the input to output divided by the gain from the
supply to the output. The PSRR is found to be
Like any low-dropout regulator, the external capacitors used
with the RT9013 must be carefully selected for regulator
stability and performance. Using a capacitor whose value
is > 1μF on the RT9013 input and the amount of capacitance
can be increased without limit. The input capacitor must
be located a distance of not more than 0.5 inch from the
input pin of the IC and returned to a clean analog ground.
Any good quality ceramic can be used for this capacitor.
The capacitor with larger value and lower ESR (equivalent
series resistance) provides better PSRR and line-transient
response.
The output capacitor must meet both requirements for
minimum amount of capacitance and ESR in all LDOs
application. The RT9013 is designed specifically to work
with low ESR ceramic output capacitor in space-saving
and performance consideration. Using a ceramic capacitor
whose value is at least 1μF with ESR is > 20mΩ on the
RT9013 output ensures stability. The RT9013 still works
well with output capacitor of other types due to the wide
stable ESR range. Figure 1. shows the curves of allowable
ESR range as a function of load current for various output
capacitor values. Output capacitor of larger capacitance
can reduce noise and improve load transient response,
stability, and PSRR. The output capacitor should be located
not more than 0.5 inch from the VOUT pin of the RT9013
and returned to a clean analog ground.
⎛
⎞
PSRR
=
20
×
log
⎜
ΔGain
Error
⎟
⎝
ΔSupply
⎠
Note that when heavy load measuring,
Δsupply
will cause
Δtemperature.
And
Δtemperature
will cause
Δoutput
voltage. So the heavy load PSRR measuring is include
temperature effect.
Current limit
The RT9013 contains an independent current limiter, which
monitors and controls the pass transistor's gate voltage,
limiting the output current to 0.6A (typ.). The output can
be shorted to ground indefinitely without damaging the part.
Thermal Considerations
Thermal protection limits power dissipation in RT9013.
When the operation junction temperature exceeds 170°C,
the OTP circuit starts the thermal shutdown function and
turns the pass element off. The pass element turn on again
after the junction temperature cools by 30°C.
For continuous operation, do not exceed absolute
maximum operation junction temperature 125°C. The
power dissipation definition in device is :
P
D
= (V
IN
−
V
OUT
) x I
OUT
+ V
IN
x I
Q
Region of Stable C
OUT
ESR vs. Load Current
100
Region of Stable C
OUT
ESR (Ω)
10
Unstable Range
1
Stable Range
0.1
0.01
RT9013-33PB, V
IN
= 5V
C
IN
= C
OUT
= 1μF/X7R
0.001
0
100
200
Unstable Range
300
400
500
Load Current (mA)
The maximum power dissipation depends on the thermal
resistance of IC package, PCB layout, the rate of
surroundings airflow and temperature difference between
junction to ambient. The maximum power dissipation can
be calculated by following formula :
P
D(MAX)
= ( T
J(MAX)
−
T
A
) /θ
JA
DS9013-05 August 2007
Figure 1
www.richtek.com
8
RICHTEK [ RICHTEK TECHNOLOGY CORPORATION ]
