欢迎访问ic37.com |
会员登录 免费注册
发布采购

RT9018B 参数 Datasheet PDF下载

RT9018B图片预览
型号: RT9018B
PDF下载: 下载PDF文件 查看货源
内容描述: 最大3A ,超低压差稳压器 [Maximum 3A, Ultra Low Dropout Regulator]
分类和应用: 稳压器
文件页数/大小: 12 页 / 143 K
品牌: RICHTEK [ RICHTEK TECHNOLOGY CORPORATION ]
 浏览型号RT9018B的Datasheet PDF文件第1页浏览型号RT9018B的Datasheet PDF文件第2页浏览型号RT9018B的Datasheet PDF文件第3页浏览型号RT9018B的Datasheet PDF文件第5页浏览型号RT9018B的Datasheet PDF文件第6页浏览型号RT9018B的Datasheet PDF文件第7页浏览型号RT9018B的Datasheet PDF文件第8页浏览型号RT9018B的Datasheet PDF文件第9页  
RT9018A/B  
Parameter  
Chip Enable  
Symbol  
Test Conditions  
Min  
Typ  
Max  
Units  
EN Input Bias Current  
I
I
V
V
= 0V  
--  
--  
12  
10  
--  
--  
20  
1
μA  
μA  
EN  
EN  
RT9018A  
VDD Shutdown  
Current  
= 0V  
SHDN  
EN  
RT9018B  
--  
Logic-Low Voltage V  
V
V
= 5V  
= 5V  
--  
--  
0.2  
--  
ENL  
ENH  
DD  
EN Threshold  
V
Logic-High Voltage V  
1.2  
--  
DD  
Power Good  
PGOOD Rising Threshold  
PGOOD Hysteresis  
PGOOD Sink Capability  
PGOOD Delay  
--  
3
90  
10  
93  
--  
%
%
I
= 10mA  
--  
0.2  
1.5  
0.4  
5
V
PGOOD  
0.5  
ms  
Thermal Protection  
Thermal Shutdown Temperature  
Thermal Shutdown Hysteresis  
Thermal Shutdown Temperature  
Fold-back  
T
--  
--  
160  
30  
--  
--  
°C  
°C  
SD  
ΔT  
SD  
V
OUT  
< 0.4V  
--  
110  
--  
°C  
Note 1. Stresses listed as the above "Absolute Maximum Ratings" may cause permanent damage to the device. These are for  
stress ratings. Functional operation of the device at these or any other conditions beyond those indicated in the  
operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended  
periods may remain possibility to affect device reliability.  
Note 2. Devices are ESD sensitive. Handling precaution recommended.  
Note 3. The device is not guaranteed to function outside its operating conditions.  
Note 4. θJA is measured in the natural convection at TA = 25°C on a high effective thermal conductivity test board (4 Layers,  
2S2P) of JEDEC 51-7 thermal measurement standard. The case point of θJC is on the expose pad for SOP-8 (Exposed  
Pad) package.  
Note 5. The dropout voltage is defined as VIN -VOUT, which is measured when VOUT is VOUT(NORMAL) - 100mV.  
Note 6. Quiescent, or ground current, is the difference between input and output currents. It is defined by IQ = IIN - IOUT under no  
load condition (IOUT = 0mA). The total current drawn from the supply is the sum of the load current plus the ground pin  
current.  
Note 7. Regulation is measured at constant junction temperature by using a 2ms current pulse. Devices are tested for load  
regulation in the load range from 1mA to 3A.  
www.richtek.com  
4
DS9018A/B-04 September 2007