ELECTRONIC COMPONENTS
RSG
■
RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany
Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de
www.rsg-electronic.de
■
■
■
■
■
Änderungen vorbehalten / subject to change without notice
750W Single Output Power Supply
SP-750
series
Features :
Universal AC input/Full range
AC input active surge current limiting
Built-in active PFC function,PF>0.96
Protections:Short circuit, overload, over voltage, over temperature
Forced air cooling by built-in DC ball bearing fan
3
High power density 5.48/inch
Built-in constant current limiting circuit
With power good and fail signal output
Built-in remote ON-OFF control
Built-in remote sense function
3 years warranty
SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT
SP-750-5
5V
120A
0 ~ 120A
600W
SP-750-12
12V
62.5A
0 ~ 62.5A
750W
120mVp-p
10 ~ 13.5V
1.0%
0.3%
0.5%
SP-750-15
15V
50A
0 ~ 50A
750W
120mVp-p
13.5 ~ 16.5V
1.0%
0.3%
0.5%
1500ms, 50ms/115VAC at full load
SP-750-24
24V
31.3A
0 ~ 31.3A
751.2W
120mVp-p
22 ~ 26.4V
1.0%
0.2%
0.5%
SP-750-27
27V
27.8A
0 ~ 27.8A
750.6W
120mVp-p
24 ~ 30V
1.0%
0.2%
0.5%
SP-750-48
48V
15.7A
0 ~ 15.7A
753.6W
120mVp-p
43 ~ 56V
1.0%
0.2%
0.5%
RIPPLE & NOISE (max.)
Note.2
120mVp-p
VOLTAGE ADJ. RANGE
4.75 ~ 5.5V
VOLTAGE TOLERANCE
Note.3
2.0%
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD TIME (Typ.)
VOLTAGE RANGE
FREQUENCY RANGE
POWER FACTOR (Typ.)
0.5%
2.0%
16ms/230VAC
90 ~ 264VAC
47 ~ 63Hz
PF>0.96/230VAC
81%
8.8A/115VAC
27A/115VAC
<2.0mA / 240VAC
1500ms, 50ms/230VAC
16ms/115VAC at full load
127 ~ 370VDC
PF>0.99/115VAC at full load
85%
4.2A/230VAC
45A/230VAC
87%
89%
89%
90%
INPUT
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVER LOAD
PROTECTION OVER VOLTAGE
OVER TEMPERATURE
POWER GOOD/FAIL
FUNCTION
REMOTE CONTROL
WORKING TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
SAFETY STANDARDS
WITHSTAND VOLTAGE
105 ~ 125% rated output power
Protection type : Constant current limiting, unit will Hiccup after 3 sec.
5.75 ~ 6.3V
13.8 ~ 16.2V
18 ~ 21V
27.6 ~ 32.4V
Protection type : Shut down o/p voltage, re-power on to recover
85
5
(TSW1 ) Detect on heatsink of power transistor
85
5
31 ~ 36.5V
57.6 ~ 67.2V
(TSW2 ) Detect on heatsink of power diode
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
50ms/1ms
Note.5
RC+/RC- short power on, open power off
-20 ~ +60 (Refer to output load derating curve)
20~90% RH non-condensing
-40 ~ +85 , 10 ~ 95% RH
0.05%/ (0 ~ 50 )
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
UL60950-1, TUV EN60950-1 Approved
I/P-O/P:3KVAC
I/P-FG:1.5KVAC
O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
SAFETY & ISOLATION RESISTANCE
EMI CONDUCTION & RADIATION
Compliance to EN55011 (CISPR11), EN55022 (CISPR22) Class B
EMC
HARMONIC CURRENT
Compliance to EN61000-3-2,-3
(Note 4)
EMS IMMUNITY
MTBF
OTHERS
NOTE
Compliance to EN61000-4-2,3,4,5,6,8,11, ENV50204, EN55024, EN61000-6-2, EN61204-3 Heavy industry level, criteria A
769.3K hrs min. MIL-HDBK-217F (25
278*127*63.5mm (L*W*H)
2.9Kg; 6pcs / 18.4Kg / 0.98CUFT
)
DIMENSION
PACKING
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
5. The power supply unit will have no output if the shorting connector is not assembled between RC+ & RC-.
File Name:SP-750-SPEC 2006-10-17
RSG [ RSG ELECTRONIC COMPONENTS GMBH ]
