SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
Specifications are typical at 25
O
C unless otherwise noted.
Specifications are subject to change without notice. Tighter
specifications available. Please contact factory.
Supply Voltage
1
_
5.0 V
+
10%
+
3.3 V
_
10%
+
_
100 ppm
Calibration Tolerance
3
+
_
Frequency Stability
50 ppm for Commercial
+
4
_
100 ppm for Industrial
Over Temperature
+
_
100 ppm for Military
Supply Current
3.3 V
5.0 V
(Typical)
10 MHz
2 mA
4 mA
24 MHz
4 mA
8 mA
30 MHz
6 mA
10 mA
40 MHz
8 mA
12 mA
50 MHz
10 mA
14 mA
CMOS
5
15 pF
Start-up Time
5 ms MAX
Rise/Fall Time
6 ns MAX
Duty Cycle
40% MIN, 60% MAX
Aging, first year
10 ppm MAX
Shock, survival
6
3,000 g, 0.3 ms,
1
/
2
sine
Vibration, survival
7
20 g , 10-2000 Hz swept sine
Operating Temp. Range -10
O
C to +70
O
C (Commercial)
-40
O
C to +85
O
C (Industrial)
-55
O
C to +125
O
C (Military)
Supply Voltage V
DD
-0.5 V to 7.0 V
Storage Temperature
-55
O
C to +125
O
C
Maximum Process Temperature 260
O
C for 20 seconds
ENABLE/DISABLE OPTIONS (E/T/N)
300 kHz to 120 MHz
2
300 kHz to 170 MHz
2
Statek offers three enable/disable options: E, T, and N.
Both the E-version and T-version have Tri-State outputs
and differ in whether the oscillator continues to run
internally when the output is put into the high Z state: it
stops in the E-version and continues to run in the
T-version. So, the E-version offers very low current
consumption when the oscillator is disabled and the
T-version offers very fast output recovery when the
oscillator is re-enabled. The N-version does not have
PIN 1 connected internally and so has no enable/disable
capability. The following table summarizes the three
options.
COMPARISON OF
ENABLE/DISABLE OPTIONS E AND T
E
When enabled (PIN 1 is high*)
Output
Oscillator
Current consumption
When disabled (PIN 1 is low)
Output
Oscillator
Current consumption
High Z state
Stops
Very low
Freq. output
Oscillates
Normal
T
Freq. output
Oscillates
Normal
Other voltages available. Contact factory.
Not all frequencies available at all voltage/enable combinations.
Other tolerances available.
Does not include calibration tolerance. Other tolerances available.
Higher CMOS loads and TTL loads available. Contact factory.
Higher shock version available. Contact factory about CXOHG.
Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also
available.
Note: All parameters are measured at ambient temperature with a 10M
Ω,15
pF load.
1.
2.
3.
4.
5.
6.
7.
High Z state
Oscillates
Lower than normal
When re-enabled (PIN 1 changes from low to high)
Output recovery
Delayed
Immediate
PACKAGING OPTIONS
CXO
- Tray Pack
- 16 mm tape, 7˝ or 13˝ reels
Per EIA 418
(see Tape and Reel data sheet 10109)
*
When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
HOW TO ORDER CXO SURFACE MOUNT CRYSTAL OSCILLATORS
CXO
S
“S” if special,
custom design,
or if the voltage
is not 5.0 V.
Otherwise,
leave blank.
T
Enable/Disable Option
E, T or N
SM3
32.0M ,
100
Calibration
Tolerance
@ 25
0
C
(in ppm)
/
100
/
/
I
Temp. Range:
C = -10
O
C to +70
O
C
I
= -40
O
C to +85
O
C
M = -55
O
C to +125
O
C
S = Customer Specified
Terminations
Frequency
Blank = SM1
K = kHz
= Gold Plated
M = MHz
SM3 = Solder Dipped
SM5 = Solder Dipped
Lead Free
Frequency
Stability over
Temp.Range
(in ppm)
OR
/
/
200
Total
Frequency
Tolerance
(in ppm)
/
I
Temp. Range:
C = -10
O
C to +70
O
C
I
= -40
O
C to +85
O
C
M = -55
O
C to +125
O
C
S = Customer Specified
10106 Rev F
S
YS
TEM
C
ERT
I
F
I
C
AT
N
IO
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256
www.statek.com
01
Pb
IS
O
90
STATEK [ STATEK CORPORATION ]
