CC2430
7.2
RF Receive Section
Measured on Texas Instruments
CC2430
EM reference design with T
A
=25°C and VDD=3.0V
unless stated otherwise.
Table 6: RF Receive Parameters
Parameter
Receiver sensitivity
Min
Typ
-92
Max
Unit
dBm
Condition/Note
PER = 1%, as specified by [1]
Measured in 50
Ω
single endedly through a balun.
[1] requires –85 dBm
Saturation (maximum input
level)
10
dBm
PER = 1%, as specified by [1]
Measured in 50
Ω
single endedly through a balun.
[1] requires –20 dBm
Adjacent channel rejection
+ 5 MHz channel spacing
Adjacent channel rejection
- 5 MHz channel spacing
Alternate channel rejection
+ 10 MHz channel spacing
Alternate channel rejection
- 10 MHz channel spacing
Channel rejection
≥
+ 15 MHz
≤
- 15 MHz
Co-channel rejection
-6
Blocking / Desensitization
+ 5 MHz from band edge
+ 10 MHz from band edge
+ 20 MHz from band edge
+ 50 MHz from band edge
- 5 MHz from band edge
- 10 MHz from band edge
- 20 MHz from band edge
- 50 MHz from band edge
Spurious emission
30 – 1000 MHz
1 – 12.75 GHz
Frequency error tolerance
±140
−64
−75
dBm
dBm
ppm
Conducted measurement in a 50
Ω
single ended
load. Complies with EN 300 328, EN 300 440 class
2, FCC CFR47, Part 15 and ARIB STD-T-66.
Difference between centre frequency of the received
RF signal and local oscillator frequency.
[1] requires minimum 80 ppm
Symbol rate error tolerance
±900
ppm
Difference between incoming symbol rate and the
internally generated symbol rate
[1] requires minimum 80 ppm
-42
-45
-26
-22
-31
-36
-24
-25
dBm
dBm
dBm
dBm
dBm
dBm
dBm
dBm
Wanted signal 3 dB above the sensitivity level, CW
jammer, PER = 1%. Measured according to EN 300
440 class 2.
dB
55
53
dB
dB
53
dB
55
dB
30
dB
41
dB
Wanted signal -88dBm, adjacent modulated channel
at +5 MHz, PER = 1 %, as specified by [1].
[1] requires 0 dB
Wanted signal -88dBm, adjacent modulated channel
at -5 MHz, PER = 1 %, as specified by [1].
[1] requires 0 dB
Wanted signal -88dBm, adjacent modulated channel
at +10 MHz, PER = 1 %, as specified by [1]
[1] requires 30 dB
Wanted signal -88dBm, adjacent modulated channel
at -10 MHz, PER = 1 %, as specified by [1]
[1] requires 30 dB
Wanted signal @ -82 dBm. Undesired signal is an
802.15.4 modulated channel, stepped through all
channels from 2405 to 2480 MHz. Signal level for
PER = 1%. Values are estimated.
Wanted signal @ -82 dBm. Undesired signal is
802.15.4 modulated at the same frequency as the
desired signal. Signal level for PER = 1%.
7.3
RF Transmit Section
Measured on Texas Instruments
CC2430
EM reference design with T
A
=25°C, VDD=3.0V, and
nominal output power unless stated otherwise.
CC2430 Data Sheet (rev. 2.1) SWRS036F
Page 13 of 211
TAOS [ TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS ]
