Electrical Specifications
Part No.
I
T(RMS)
V
DRM
V
BO
Breakover Voltage
50/60Hz Sine Wave
(1)
I
DRM
I
BO
Type
On-State
Repetitive
RMS Current
Peak
T
J
≤125°C
Off-State
50/60Hz
Voltage
Sine Wave
(7) (8)
Repetitive Breakover
Current
Peak
50/60Hz
Off-State
Current Sine Wave
50/60Hz
Sine Wave
V=V
DRM
DO-15X
TO-92
TO-202AB
DO-214AA
G Package
E Package
F Package
S Package
K1050E70
K1100E70
K1200E70
K1300E70
K1400E70
K1500E70
K2000E70
K2200E70
K2400E70
K2500E70
K1050G
K1100G
K1200G
K1300G
K1400G
K1500G
K2000G
K2200G
K2400G
K2500G
K2000F1
K2200F1
K2400F1
K2401F1
K2500F1
K3000F1
K2500S
K1050S
K1100S
K1200S
K1300S
K1400S
K1500S
K2000S
K2200S
K2400S
Amps
MAX
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0 (10)
1.0
1.0
Volts
MIN
±90
±90
±90
±90
±90
±90
±180
±180
±190
±190
±190
±190
Volts
MIN
95
104
110
120
130
140
190
205
220
220
240
270
MAX
113
118
125
138
146
170
215
230
250
250
280
330
µAmps
MAX
5
5
5
5
5
5
5
5
5
5
5
5
µAmps
MAX
10
10
10
10
10
10
10
10
10
10
10
10
General Notes
•
•
•
All measurements are made at 60Hz with a resistive load at an
ambient temperature of +25°C unless otherwise specified.
Storage temperature range (T
S
) is -65°C to +150°C.
The case (T
C
) or lead (T
L
) temperature is measured as shown on
the dimensional outline drawings. See “Package Dimensions” sec-
Junction temperature range (T
J
) is -40°C to +125°C.
Lead solder temperature is a maximum of +230°C for 10 seconds
maximum;
≥
1/16" (1.59mm) from case.
Electrical Specification Notes
(1)
(2)
(3)
(4)
(5)
(6)
(7)
See Figure 9.6 for V
BO
change vs junction temperature.
See Figure 9.7 for I
BO
vs junction temperature.
See Figure 9.2 for I
H
vs case temperature.
See Figure 9.14 for test circuit.
See Figure 9.1 for more than one full cycle rating.
R
θJA
for TO-202 Type 23 and Type 41 is 70°C/watt.
T
C
≤
90°C for TO-92 Sidac and T
C
≤
105°C for TO-202 Sidacs.
T
L
≤
100°C for DO-15X and T
L
≤
90°C for DO-214AA.
(8) See Figure 9.15 for clarification of Sidac operation.
(9) For best Sidac operation, the load impedance should be near or
less than switching resistance.
(10) Teccor's new, improved series of sidacs is designed to ensure
goodcommutationathigherswitchingfrequencies asrequiredinignitor
circuits for high intensity discharge (HID) lighting. A typical circuit
for a metal halide lamp ignitor is shown in the schematic, Figure
pulses for ignition of Osram lamp types such as HQI-T70W, HQI-
T150W, and HQI-T250W which require a minimum of three pulses
at 4kV magnitude and >1µs duration each at a minimum repetition
rate of 3.3kHz.
•
•
SIDAC
9-2
Teccor Electronics
(972) 580-7777
TECCOR [ TECCOR ELECTRONICS ]
