Data Sheets
Sensitive Triacs
V
TM
(1) (4)
V
GT
(2) (5) (15)
I
H
(1) (7)
I
GTM
(13)
P
GM
(13)
P
G(AV)
I
TSM
(8) (10)
dv/dt(c)
(1) (10)
dv/dt
(1)
t
gt
(9)
I
2
t
di/dt
Volts
T
C
= 25 °C
MAX
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
Volts
T
C
= 25 °C
MAX
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
mAmps
MAX
10
10
10
10
10
10
20
20
20
10
10
10
20
20
20
Amps
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
Watts
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
Watts
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
Amps
60/50 Hz
60/50
60/50
60/50
60/50
60/50
60/50
60/50
60/50
60/50
80/65
80/65
80/65
80/65
80/65
80/65
Volts/µSec
TYP
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
Volts/µSec
T
C
= 100 °C
TYP
40
30
20
40
30
20
45
40
30
40
30
20
45
40
30
µSec
TYP
3
3
3
3
3
3
3.2
3.2
3.2
3
3
3
3.2
3.2
3.2
Amps
2
Sec
15
15
15
15
15
15
15
15
15
26.5
26.5
26.5
26.5
26.5
26.5
Amps/µSec
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
Electrical Specification Notes
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
For either polarity of MT2 with reference to MT1 terminal
For either polarity of gate voltage V
GT
with reference to MT1
terminal
See Gate Characteristics and Definition of Quadrants.
See Figure E1.4 for i
T
versus v
T
.
See Figure E1.6 for V
GT
versus T
C
.
See Figure E1.7 for I
GT
versus T
C
.
See Figure E1.5 for I
H
versus T
C
.
See Figure E1.9 for surge rating and specific duration.
See Figure E1.8 for t
gt
versus I
GT
.
Gate Characteristics
Teccor triacs may be turned on between gate and MT1 terminals
in the following ways:
•
•
In-phase signals (with standard AC line) using Quadrants I
and III
Application of unipolar pulses (gate always positive or nega-
tive), using Quadrants II and III with negative gate pulses and
Quadrants I and IV with positive gate pulses
When maximum surge capability is required, pulses should be a
minimum of one magnitude above I
GT
rating with a steep rising
waveform (
≤
1 µs rise time).
ALL POLARITIES ARE REFERENCED TO MT1
MT2 POSITIVE
(Positive Half Cycle)
(10) See Figure E1.2 and Figure E1.3 for maximum allowable case
temperature at maximum rated current.
(11) See Figure E1.1, Figure E1.2, and Figure E1.3 for T
A
or T
C
versus
I
T(RMS)
.
(12) See package outlines for lead form configurations. When ordering
special lead forming, add type number as suffix to part number.
(13) Pulse width
≤10
µs
(14) T
C
or T
L
= T
J
for test conditions in off state
(15) Minimum non-trigger V
GT
at 110 °C is 0.2 V.
I
GT
(
-
)
MT2
I
GT
GATE
+
MT2
(+)
I
GT
GATE
MT1
MT1
-
(
-
)
REF
MT2
I
GT
GATE
MT1
REF
QII QI
QIII QIV
(+)
REF
+
MT2
I
GT
GATE
MT1
REF
I
GT
MT2 NEGATIVE
(Negative Half Cycle)
-
Definition of Quadrants
©2004 Littelfuse LP
Thyristor Product Catalog
E1 - 5
http://www.teccor.com
+1 972-580-7777
TECCOR [ TECCOR ELECTRONICS ]
