SERIES RF170
GENERAL ELECTRICAL SPECIFICATIONS
Contact Arrangement
Rated Duty
Contact Resistance
Contact Load Rating (DC)
Contact Life Ratings
Contact Overload Rating
Contact Carry Rating
Coil Operating Power
Operate Time
Minimum Operate Pulse
lntercontact Capacitance
Insulation Resistance
Dielectric Strength
(@ 25°C) (Notes 1 & 2)
2 Form C (DPDT)
Continuous
0.15 ohm max. before life; 0.25 ohm max. after life at 0.25A/28VDC, (measured 1/8” from header)
Resistive:
Low Level:
0.25 Amp/28VDC
10 to 50 µA/10 to 50 mV
10,000,000 cycles (typical) at low level
00,100,000
cycles min. at all other loads specified above
0.5A/28VDC Resistive (100 cycles min.)
Contact factory
290 milliwatts typical at nominal rated voltage @ 25°C
2.0 msec max. at nominal rated coil voltage
6.0 msec max. at nominal voltage
0.02 pf typical
1,000 megohms min. between mutually isolated terminals
Atmospheric pressure: 350 VRMS/60 Hz
DETAILED ELECTRICAL SPECIFICATIONS
(@ 25°C) (Note 2)
BASE PART
NUMBERS
Coil Voltage (VDC)
Nom.
Max.
Coil Resistance (Ohms ± 20%)
Set & Reset Voltage (VDC, Max.)
±
RF170-5
RF170-6
RF170-9
RF170-12
RF170-18
RF170-26
5.0
6.0
61
3.5
6.0
8.0
120
4.5
9.0
12.0
280
6.8
12.0
16.0
500
9.0
18.0
24.0
1130
13.5
26.5
32.0
2000
18.0
TYPICAL R.F. PERFORMANCE (NOTE 1)
OUTLINE DIMENSIONS
.335 MAX.
(8.51)
.435 MAX.
(11.05)
0
.1
.2
.3
.4
dB
.375 MAX.
(9.53)
(.031 ± .003)
(0.79 ± 0.08)
.75 MIN. (19.05)
0.17 + .002
– .001
DIA.
(0.43) + (0.051)
– (0.025)
10 LEADS
9
INSERTIO
N LOSS
.300 MAX.
(7.62)
10
20
30
40
50
60
70
.01
0.5
.1
FREQUENCY (GHz)
SS
CRO
1.92
N
RETUR
SW
LOSS (V
R)
S
TACT
1.22
1.07
VSWR
.035 ± .010
(0.89 ± 0.25)
1
CON
1.02
1.01
1.00
1.00
4.0
10
NA
POLES
ATIO
A
C
R
O
SS
ISOL
ATION
ISOL
.100 TYP. (2.54)
COIL B
8
7
6
5
2
3
4
.475 MAX.
(12.06)
.5
1.0
COIL A
PIN NUMBERS
FOR REF. ONLY
.200
(5.08)
SCHEMATIC
(TERMINAL VIEW) (NOTE 4)
DIMENSIONS ARE SHOWN IN INCHES (MILLIMETERS)
NOTES:
1.
2.
3.
4.
Characteristics shown as “typical” are based on available data and are best estimates. No on-going verification tests are performed.
Unless otherwise specified, parameters are initial values.
Relays will exhibit no contact chatter in excess of 10 µsec or transfer in excess of 1 µsec.
Contacts shown in position resulting when Coil A last energized.
©1996
TELEDYNE RELAYS
12525 Daphne Avenue
Hawthorne, California 90250
88
TELEDYNE [ TELEDYNE TECHNOLOGIES INCORPORATED ]
