AGR26125E
125 W, 2.5 GHz—2.7 GHz, N-Channel E-Mode, Lateral MOSFET
Introduction
The AGR26125E is a high-voltage, gold-metalized,
enhancement mode, laterally diffused metal oxide
semiconductor (LDMOS) RF power transistor suit-
able for ultrahigh-frequency (UHF) applications
including multichannel multipoint distribution service
(MMDS) for broadcasting and communications.
)
Table 1. Thermal Characteristics
Parameter
Thermal Resistance,
Junction to Case:
AGR26125EU
AGR26125EF
Sym
R
ı
JC
R
ı
JC
Value
0.5
0.5
Unit
°C/W
°C/W
Table 2. Absolute Maximum Ratings*
Parameter
Drain-source Voltage
Gate-source Voltage
Total Dissipation at T
C
= 25 °C:
AGR26125EU
AGR26125EF
Derate Above 25
°C:
AGR26125EU
AGR26125EF
Operating Junction Tempera-
ture
Storage Temperature Range
Sym Value Unit
V
DSS
65
Vdc
V
GS
–0.5, +15 Vdc
P
D
P
D
—
—
T
J
350
350
2.0
2.0
200
W
W
W/°C
W/°C
°C
AGR26125EU (unflanged)
AGR26125EF (flanged)
5B 03 STYLE 1
Figure 1. Available Packages
Features
Typical pulsed P1dB, 6 µs pulse at 10% duty: 125 W.
Typical performance for MMDS systems.
f = 2600 MHz, I
DQ
= 1300 mA, Vds = 28 V,
adjacent channel BW = 3.84 MHz, 5 MHz offset;
alternate channel BW = 3.84 MHz, 10 MHz offset.
Typical P/A ratio of 9.8 dB at 0.01% (probability)
CCDF*:
— Output power: 20 W
— Power gain: 11.5 dB.
— Power Added Efficiency (PAE): 19%.
— ACLR1: –35 dBc.
— ACLR2: –37 dBc.
High-reliability, gold-metalization process.
Low hot carrier injection (HCI) induced bias drift
over 20 years.
Internally matched.
High gain, efficiency, and linearity.
Integrated ESD protection.
Device can withstand a 10:1 voltage standing wave
ratio (VSWR) at 28 Vdc, 2600 MHz, 125 W contin-
uous wave (CW) output power.
Large signal impedance parameters available.
*The test signal utilized is 4-channel W-CDMA Test Model 1. This
test signal provides an equivalent reference (occupied bandwidth
and waveform EPF) for the actual performance with an MMDS
waveform.
T
STG
–65, +150 °C
* Stresses in excess of the absolute maximum ratings can cause
permanent damage to the device. These are absolute stress rat-
ings only. Functional operation of the device is not implied at
these or any other conditions in excess of those given in the
operational sections of the data sheet. Exposure to absolute
maximum ratings for extended periods can adversely affect
device reliability.
Table 3. ESD Rating*
AGR26125E
HBM
MM
CDM
Minimum (V)
500
50
1500
Class
1B
A
4
* Although electrostatic discharge (ESD) protection circuitry has
been designed into this device, proper precautions must be
taken to avoid exposure to ESD and electrical overstress (EOS)
during all handling, assembly, and test operations.
PEAK Devices
Agere
employs a human-body model (HBM), a machine model (MM),
and a charged-device model (CDM) qualification requirement in
order to determine ESD-susceptibility limits and protection
design evaluation. ESD voltage thresholds are dependent on the
circuit parameters used in each of the models, as defined by
JEDEC's JESD22-A114B (HBM), JESD22-A115A (MM), and
JESD22-C101A (CDM) standards.
Caution: MOS devices are susceptible to damage from elec-
trostatic charge. Reasonable precautions in han-
dling and packaging MOS devices should be
observed.
TRIQUINT [ TRIQUINT SEMICONDUCTOR ]
