欢迎访问ic37.com |
会员登录 免费注册
发布采购

Current 参数 Datasheet PDF下载

Current图片预览
型号: Current
PDF下载: 下载PDF文件 查看货源
内容描述: 双频HPLL VCXO [Dual Frequency HPLL VCXO]
分类和应用: 石英晶振压控振荡器
文件页数/大小: 9 页 / 727 K
品牌: VECTRON [ Vectron International, Inc ]
 浏览型号Current的Datasheet PDF文件第1页浏览型号Current的Datasheet PDF文件第2页浏览型号Current的Datasheet PDF文件第3页浏览型号Current的Datasheet PDF文件第5页浏览型号Current的Datasheet PDF文件第6页浏览型号Current的Datasheet PDF文件第7页浏览型号Current的Datasheet PDF文件第8页浏览型号Current的Datasheet PDF文件第9页  
VX-722 Dual Frequency HPLL VCXO
LVPECL Applica on Diagrams
+3.3V
VC
10nF
1nF
1
6
10nF
FS
2
5
10nF
3
4
240
240
+3.3V
VC
10nF
+3.3V
1nF
1
6
130
FS
2
5
10nF
3
4
82
82
130
10nF
Figure 6 - Single Resistor Termina on Scheme
Resistor values are typically 120 to 240 ohms for 3.3V opera on and 82 to 120 ohms for 2.5V
opera on.
Figure 7 - Pull Up Pull Down Termina on
Resistor values are typically for 3.3V opera on
For 2.5V opera on, the resistor to ground is 62 ohms and the resistor to supply is 240 ohms
There are numerous applica on notes on termina ng and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6,
and a pull-up/pull-down scheme as shown in Figure 7. An AC coupling capacitor is op onal, depending on the applica on and the input logic requirements of
the next stage.
One of the most important considera ons is termina ng the Output and Complementary Outputs equally. An unused output should not be le un-
terminated, and if one of the two outputs is le open it will result in excessive ji er on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to ji er related problems.
LVDS Applica on Diagrams
+3.3V
VC
10nF
1nF
1
6
1
6
10nF
FS
2
5
100
3
4
10nF
VC
+3.3V
10nF
1nF
FS
2
5
Receiver
100
Receiver
3
4
Figure 8 - LVDS to LVDS, internal 100Ω
Some LVDS structures have an internal 100 ohm resistor on the
input and do not need addi onal components.
Figure 9 - LVDS to LVDS, External 100Ω and AC block ing caps
One of the most important considera ons is termina ng the Output and Complementary Outputs equally. An unused output should not be le un-
terminated, and if one of the two outputs is le open it will result in excessive ji er on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to ji er related problems.
Page 4 of 9
Vectron Interna onal • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • h p://www.vectron.com
Rev2: 14 November 2012