Production Data
WM9715L
NAME
DBVDD
XTLIN
XTLOUT
DGND1
SDATAOUT
BITCLK
DGND2
SDATAIN
DCVDD
SYNC
RESETB
WIPER / AUX4
TPVDD
X+/BR
Y+/TR
X-/TL
Y-/BL
TPGND
PCBEEP
PHONE
MIC1
MIC2
LINEINL
LINEINR
AVDD
AGND
VREF
MICBIAS
COMP1 / AUX1
COMP2 / AUX2
BMON / AUX3
CAP2
MONOOUT
SPKGND
LOUT2
ROUT2
OUT3
SPKVDD
HPOUTL
HPGND
HPOUTR
AGND2
HPVDD
DNC
GENIRQ
PENDOWN
ADCIRQ
SPDIF_OUT
TYPE
Supply
Digital Input
Digital Output
Supply
Digital Input
Digital Output
Supply
Digital Output
Supply
Digital Input
Digital Input
Analogue Input
Supply
Analogue Input
Analogue Input
Analogue Input
Analogue Input
Supply
Analogue Input
Analogue Input
Analogue Input
Analogue Input
Analogue Input
Analogue Input
Supply
Supply
Analogue Output
Analogue Output
Analogue Input
Analogue Input
Analogue Input
Analogue In / Out
Analogue Output
Supply
Analogue Output
Analogue Output
Analogue Output
Supply
Analogue Output
Supply
Analogue Output
Supply
Supply
Do not connect
Digital In / Out
Digital Output
Digital In / Out
Digital In / Out
Digital I/O Buffer Supply
Clock Crystal Connection 1 / External Clock Input
Clock Crystal Connection 2
Digital Ground (return path for both DCVDD and DBVDD)
Serial Data Output from Controller / Input to WM9715L
Serial Interface Clock Output to Controller
Digital Ground (return path for both DCVDD and DBVDD)
Serial Data Input to Controller / Output from WM9715L
Digital Core Supply
Serial Interface Synchronisation Pulse from Controller
Reset (asynchronous, active Low, resets all registers to their default)
Top Sheet Connection for 5-wire Touchpanels / Auxiliary ADC Input
Touchpanel Driver Supply
Touchpanel Connection: X+ (Right) for 4-wire / bottom right for 5-wire
Touchpanel Connection: Y+ (Top) for 4-wire / top right for 5-wire
Touchpanel Connection: X- (Left) for 4-wire / top left for 5-wire
Touchpanel Connection: Y- (Bottom) for 4-wire / bottom left for 5-wire
Touchpanel Driver Ground
Line Input to analogue audio mixers, typically used for beeps
Phone Input (RX)
Left Microphone or Microphone 1 Input
Right Microphone or Microphone 2 Input
Left Line Input
Right Line Input
Analogue Supply (feeds audio DACs, ADCs, PGAs, mic boost,
mixers)
Analogue Ground
Internal Reference Voltage (buffered CAP2)
Bias Voltage for Microphones (buffered CAP2
×
1.8)
Comparator 1 (dead battery alarm) / Auxiliary ADC Input 1
Comparator 2 (low battery alarm) / Auxiliary ADC Input 2
Battery Monitor Input / Auxiliary ADC Input 3
Internal Reference Voltage (normally AVDD/2, if not overdriven)
Mono Output, intended for Phone TX signal
Speaker Ground (feeds output buffers on pins 35 and 36)
Left Output 2 (Speaker, Line or Headphone)
Right Output 2 (Speaker, Line or Headphone)
Analogue Output 3 (from AUXDAC or headphone pseudo-ground)
Speaker Supply (feeds output buffers on pins 35 and 36)
Headphone Left Output
Headphone Ground (feeds output buffers on pins 37, 39, 41)
Headphone Right Output
Analogue Ground, Chip Substrate
Headphone Supply (feeds output buffers on pins 37, 39, 41)
Leave this pin unconnected
General IRQ (Interrupt Request) Output
Indicates that screen is being touched
AUXADC “data ready” interrupt; also determines power up status.
(See “Power Management” and “Applications” sections)
SPDIF Digital Audio Output
DESCRIPTION
PIN DESCRIPTION
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
Note:
It is recommended that the QFN ground paddle should be connected to analogue ground on the application PCB.
w
PD Rev 4.0 December 2007
5