X25F128
ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias .................. –65°C to +135°C
Storage Temperature ....................... –65°C to +150°C
Voltage on any Pin with Respect to V
SS .........
–1V to +7V
D.C. Output Current ............................................. 5mA
Lead Temperature
(Soldering, 10 Seconds) ............................. 300°C
*COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and the functional operation
of the device at these or any other conditions above
those listed in the operational sections of this specification
is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Temp
Commercial
Extended
Industrial
Min.
0°C
–20°C
–40°C
Max.
+70°C
+85°C
+85°C
6829 PGM T06.1
Supply Voltage
X25F128
X25F128–5
Limits
1.8V to 3.6V
4.5V to 5.5V
6829 PGM T07.1
D.C. OPERATING CHARACTERISTICS
(Over the recommended operating conditions unless otherwise specified.)
Limits
Symbol
I
CC
I
SB1(2)
I
SB2
I
LI
I
LO
V
IL(1)
V
IH(1)
V
OL1
V
OH1
V
OL2
V
OH2
Parameter
V
CC
Supply Current (Active)
Min.
Max.
5
Units
mA
µA
µA
µA
µA
V
V
V
V
V
V
Test Conditions
SCK = V
CC
x 0.1/V
CC
x 0.9 @ 1MHz,
SO = OPEN,
CS
=
V
SS
CS
= V
CC
, V
IN
=
V
SS
or V
CC,
V
CC
= 3.6V
CS
= V
CC
, V
IN
=
V
SS
or V
CC,
V
CC
= 5V
V
IN
=
V
SS
to V
CC
V
OUT
=
V
SS
to V
CC
V
CC
Supply Current (Standby)
1
V
CC
Supply Current (Standby)
10
Input Leakage Current
10
Output Leakage Current
10
Input LOW Voltage
–0.5
V
CC
x 0.3
Input HIGH Voltage
V
CC
x 0.7 V
CC
+ 0.5
Output LOW Voltage
0.4
Output HIGH Voltage
V
CC
– 0.3
Output LOW Voltage
0.4
Output HIGH Voltage
V
CC
– 0.8
I
OL
= 1.5mA, V
CC
= 2.7V
I
OH
= –0.4mA, V
CC
= 2.7V
I
OL
= 3mA, V
CC
= 5V
I
OH
= –1.6mA, V
CC
= 5V
6829 PGM T08.1
POWER-UP TIMING
Symbol
t
PUR(3)
t
PUW(3)
Parameter
Power-up to Read Operation
Power-up to Write Operation
Min.
Max.
1
5
Units
ms
ms
6829 PGM T09
CAPACITANCE
T
A
= 25°C, f = 1MHz, V
CC
= 5V.
Symbol
C
OUT(2)
C
IN(2)
Notes:
Test
Output Capacitance (SO)
Input Capacitance (SCK, SI,
CS, PP, HOLD)
Max.
8
6
Units
pF
pF
Conditions
V
OUT
= 0V
V
IN
= 0V
6829 PGM T10
(1) V
IL
min. and V
IH
max. are for reference only and are not tested.
(2) This parameter is periodically sampled and not 100% tested.
(3) t
PUR
and t
PUW
are the delays required from the time V
CC
is stable until the specified operation can be initiated. These parameters
are periodically sampled and not 100% tested.
8
XICOR [ XICOR INC. ]
