X9241
ABSOLUTE MAXIMUM RATINGS*
Temperature under Bias .................. –65°C to +135°C
Storage Temperature ....................... –65°C to +150°C
Voltage on SCK, SCL or any Address Input
with Respect to V
SS ...................................
–1V to +7V
Voltage on any V
H
or V
L
Referenced to V
SS .........
±8V
∆V
= |V
H
–V
L
| ......................................................... 16V
Lead Temperature (Soldering, 10 seconds)...... 300°C
RECOMMENDED OPERATING CONDITIONS
Temperature
Commercial
Industrial
Military
Min.
0°C
–40°C
–55°C
Max.
+70°C
+85°C
+125°C
3864 PGM T03
*COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and the functional operation of
the device at these or any other conditions above those
indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect device reliability.
Supply Voltage
X9241
Limits
5V
±10%
3864 PGM T04.1
ANALOG CHARACTERISTICS
(Over recommended operating conditions unless otherwise stated.)
Symbol
R
TOTAL
I
W
R
W
V
TERM
Parameter
End to End Resistance
Power Rating
Wiper Current
Wiper Resistance
Voltage on any V
H
or
or V
L
Pin
Noise
Resolution
(4)
Absolute Linearity
(1)
Relative Linearity
(2)
Temperature Coefficient
Min.
–20
–1
40
–5
≤120
1.6
–1
–0.2
±300
Limits
Typ.
Max.
+20
50
+1
100
+5
Units
%
mW
mA
Ω
V
dB/
%
MI
(3)
MI
(3)
ppm/°C
Test Conditions
25°C, each pot
Wiper Current =
±
1mA
Ref: 1V
V
w(n)(actual)
– V
w(n)(expected)
V
w(n + 1)
– [V
w(n) + MI
]
3864 PGM T05.2
0.4
+1
+0.2
D.C. OPERATING CHARACTERISTICS
(Over recommended operating conditions unless otherwise stated.)
Symbol
Parameter
l
CC
Supply Current (Active)
I
SB
I
LI
I
LO
V
IH
V
IL
V
OL
V
CC
Current (Standby)
Input Leakage Current
Output Leakage Current
Input HIGH Voltage
Input LOW Voltage
Output LOW Voltage
Min.
Limits
Typ.
Max.
3
200
500
10
10
V
CC
+ 1
0.8
0.4
Units
mA
µA
µA
µA
V
V
V
Test Conditions
f
SCL
= 100KHz, SDA = Open,
Other Inputs = V
SS
SCL=SDA=V
CC
, Addr. = V
SS
V
IN
= V
SS
to V
CC
V
OUT
= V
SS
to V
CC
2
–1
I
OL
= 3mA
3864 PGM T06.3
Notes:
(1) Absolute Linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper
position when used as a potentiometer.
(2) Relative Linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a
potentiometer. It is a measure of the error in step size.
(3) MI = RTOT/63 or (V
H
– V
L
)/63, single pot
(4) Max. = all four arrays cascaded together, Typical = individual array resolutions.
9
XICOR [ XICOR INC. ]
