AC-DC
130 Watts
JPS130/JPS130-M Series
•
•
•
•
•
•
•
High Efficiency - up to 90%
xppower.com
Medical Approval (JPS130-M Versions)
3” x 5” Footprint
Zero Voltage Switching Technology
High Power Density
100 W Convection-cooled
Single & Multi Outputs
Specification
Input
Input Voltage
Input Frequency
Input Current
Inrush Current
Power Factor
Earth Leakage Current
Input Protection
90-264 VAC (130-370 VDC)
47-63 Hz
2.0/1.0 A max at 115/230 VAC
30 A at 115 VAC, 60 A at 230 VAC
0.9 typical
1.5 mA max at 264 VAC/60 Hz JPS130
250 µA max at 240 VAC/60 Hz JPS130-M
• Internal 3.15 A/250 V fuse
Both line & neutral fused (JPS130-M)
•
•
•
•
•
•
General
Efficiency
Isolation
• Up to 90% nominal line, full load
• 3000 VAC Input to Output (JPS130),
4000 VAC Input to Output (JPS130-M),
1500 VAC Input to Ground,
500 VAC Output to Ground
• 120 kHz fixed, ±10% for both active
PFC & PWM
• 6.7 W/In
3
• 250 kHrs per MIL-HDBK-217F at 25 °C
Switching Frequency
Power Density
MTBF
Environmental
Output
• See table
• ±10% on single output models,
±5% on multi output models, other
voltages will track by the same percentage
Initial Set Accuracy
• At 60% rated load ±1% single outputs,
±3% on V1 for multi outputs
Minimum Load
• Single output: no minimum load required
Multi-outputs: (see note 1)
Start Up Rise Time
• <20 ms
Hold Up Time
• 16 ms typical at low line
Line Regulation
• ±0.5% Vmin to Vmax
Load Regulation
• ±1%, ±5% for auxiliaries, 20-100%
of rated load
Transient Response
• 4% max deviation, recovery to within
1% in 500 µs for a 25% load change
Ripple & Noise
• ±1% max pk-pk (see note 4)
Overvoltage Protection
• 110-140% on V1 only,
recycle input to reset
Overload Protection
• 110-150%, auto recovery
Short Circuit Protection
• Trip & restart (Hiccup mode)
Temperature
• 0.05%/°C
Coefficient
Remote Sense
• Single output models only, compensates
for up to 0.5 V drop
Fan Output
• 12 V, 450 mA multi-output models only
Output Voltage
Output Voltage Trim
Operating Temperature
• 0 °C to +70 °C, (see derating curves)
Cooling
• 130 W with 18 CFM airflow,
100 W with convection cooling
Operating Humidity
• 5-95% RH, non-condensing
Storage Temperature
• -20 °C to +85 °C
Operating Altitude
• 3000 m
EMC & Safety
Emissions
Harmonic Currents
Voltage Flicker
ESD Immunity
Radiated Immunity
EFT/Burst
Surge
Conducted Immunity
Dips & Interruptions
Safety Approvals
• EN55022, level B conducted
FCC 20780, level B conducted
• EN61000-3-2
• EN61000-3-3
• EN61000-4-2, level 3 Perf Criteria A
• EN61000-4-3, 10 V/m Perf Criteria A
• EN61000-4-4, level 3 Perf Criteria A
• EN61000-4-5, level 3 Perf Criteria A
• EN61000-4-6, 3 V Perf Criteria A
• EN61000-4-11, 30% 10 ms, 60% 100 ms,
95% 5000 ms Perf Criteria A, B, B
• JPS130:
EN60950-1:2001, UL60950-1,
CSA C22.2 No. 60950-1,
CE Mark LVD.
JPS130-M: UL2601-1, EN60601-1,
CSA C22.2 No. 601.1
CE Mark LVD.
XPPOWER [ XP POWER LIMITED ]
