Capacitors
Continued from the preceding page.
Specifications
No.
Item
Temperature
Compensating Type
Test Method
High Dielectric Type
The measured and observed characteristics should satisfy the
specifications in the following table
Appearance
No defects or abnormalities
B1, B3, R1, R6, R7
: Within
T12.5%
F1, F5, E4 : Within
T30%
[W.V. : 10Vmax.]
F1, F5 : Within
W30/Y40%
[B1, B3, R1, R6, R7, E4]
W.V. : 25Vmin. : 0.05max.
W.V. : 16/10V : 0.05max.
W.V. : 6.3V
: 0.075max. (CF3.3µF)
: 0.125max. (CU3.3µF)
[F1, F5]
W.V. : 25Vmin.
: 0.075max. (CF0.1µF)
: 0.125max. (CU0.1µF)
W.V. : 16V/10V : 0.15max.
W.V. : 6.3V : 0.2max.
Capacitance
Change
Within
T7.5%
or
T0.75pF
(Whichever is larger)
17
Humidity
Load
30pF and over : QU200
30pF and below :
QU100W10C/3
C : Nominal Capacitance (pF)
Apply the rated voltage at 40T2D and 90 to 95% humidity for
500T12 hours. Remove and set for 24T2 hours (temperature
compensating type) or 48T4 hours (high dielectric constant
type) at room temprature, then muasure. The charge/discharge
current is less than 50mA.
#Initial
measurement for F1, F5/10V max.
Apply the rated DC voltage for 1 hour at 40T2D.
Remove and set for 48T4 hours at room temperature.
Perform initial measurement.
Q/D.F.
I.R.
More than 500MΩ or 25Ω • F (Whichever is smaller)
The measured and observed characteristics should satisfy the
specifications in the following table
Appearance
No defects or abnormalities
B1, B3, R1, R6, R7
: Within
T12.5%
F1, F5, E4 : Within
T30%
[Exept 10Vmax. and.
CU1.0µF]
F1, F5 : Within
W30/Y40%
[10Vmax. and. CU1.0µF]
[B1, B3, R1, R6, R7, E4]
W.V. : 25Vmin. : 0.04max.
W.V. : 16/10V : 0.05max.
W.V. : 6.3V
: 0.075max.(CF3.3µF)
: 0.125max.(CU3.3µF)
[F1, F5]
W.V. : 25Vmin.
: 0.075max.(CF0.1µF)
: 0.125max.(CU0.1µF)
W.V. : 16V/10V : 0.15max.
W.V. : 6.3V : 0.2max.
Capacitance
Change
Within
T3%
or
T0.3pF
(Whichever is larger)
18
High
Temperature
Load
Apply 200% of the rated voltage at the maximum operating
temperature
T3D
for 1000T12 hours.
Set for 24T2 hours (temperature compensating type)
or 48T4 hours (high dielectric constant type) at room
temperature, then measure.
The charge/discharge current is less than 50mA.
#Initial
measurement for high dielectric constant type.
Apply 200% of the rated DC voltage at the maximun operating
temperature
T3D
for one hour. Remove and set for 48T4
hours at room temperature.
Perform initial measurement.
Q/D.F.
30pF and over : QU350
10pF and over
30pF and below :
QU275W2.5C
10pF and below :
QU200W10C
C : Nominal Capacitance (pF)
I.R.
More than 1,000MΩ or 50Ω
#
F (Whichever is smaller)
Continued on the following page.
!Note
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specification or transact the approval sheet for product specification
before ordering. Especially, please read rating and
!CAUTION
(for storage and operating, rating, soldering and mounting, handling) in them to prevent smoking and/or burning, etc.
• You are able to read a detailed specification in the website (http://search.murata.co.jp/) before to require our product specification or to transact the approval sheet for product specification.
ETC [ ETC ]
