Series 811 Mighty Mouse High Density (HD)
Contacts and Tools
band-Master™ Advanced Termination System
bands and instructions
glenair Band-Master™ Advanced Termination System: How To Order
1
Fast, cost-effective shield termination. Attach cable shields to backshells with Band-Master™ ATS stainless
steel straps.The Band-Master™ ATS system offers fast termination and the flexibility to handle a wide range
of parts with just one band size. Approved for aerospace and defense, these straps have successfully passed
rigorous shock, vibration and environmental testing.
Band installationTool. Use with .240" (6.10 mm)
Standard Band, .240" (6.10 mm) wide. Available
1ꢀwide bands. 6.75 inches (172 mm) length, 1.2 2ꢀin two lengths, flat or pre-coiled. Stainless steel.
pounds (0.6 Kg.)
Figure
Description
Part Number
ꢀ
Band installation Tool
600-058
Length
in.
ꢀꢂ.ꢁꢃꢄ 3ꢅꢁ.ꢀ
ꢀ8.ꢄꢄꢄ ꢂꢃꢆ.ꢁ
Part Number
Accommodates Diameter
Figure
mm
Flat
600-052
600-090
Pre-Coiled
600-052-1
600-090-1
in.
ꢀ.8
mm
ꢂꢃ.ꢆ
ꢅ3.ꢃ
ꢁ
ꢁ
ꢁ.ꢃ
Contact Glenair or visit our website (glenair.com) to view our complete line of Band-Master™ ATS products,
including pneumatic tools for high volume production and calibration kits.
2
LENGTH ± .060 (1.5)
.240 (6.10)
.350 (8.9)
TAIL LENGTH
INDICA OR MARK
INDICA OR MTARK
Band-Master™ ATS Shield Termination instructions
Adapter
Retention Lip
Conductors
.400 (1.2mm) Min.
Length Braid Over
Termination Area
Braid
1. Prepare Cable Braid for termination process Shield Termination
(Figure 1).
Clamping Process (Figures 4 thru ꢈ)
Adapter
incline
2. PushBraidforwardoverAdapterRetentionLip
to the Adapter incline Point (or .4" [10.2mm]
minimumbraidlength).MilkBraidasrequired
to remove slack and insure a snug fit around
the shield termination area (Figure 2).
2
1
NOTE:TofreeToolHandles,moveHoldingClips
to center of Tool.
4. Squeeze Gripper Release Lever and insert
Band into the front end opening of the
Tool. (NOTE: Circular portion of looped
band must always face downward.)
5. AligningtheBandandToolwiththeShield
Termination Area, squeeze Black Pull-Up
Handlerepeatedlyusingshortstrokesuntil
it locks against Tool Body. (This indicates
the Band is compressed to the Tool Preca-
librated Tension.)
ꢇ. Prepare the Band in the following manner:
IMPORTANT: Due to Connector/Adapter cir-
cumference, it may be necessary to prepare
the Band around the Cable or Retention Area.
A. Roll Band through the Buckle Slot twice.
(Bands must be double-coiled.)
B. Pull on Band until Mark ( ) is within ap-
proximately .250 inch (6.4mm) of Buckle
Slot(Figureꢇ).TheBandmaybetightened
further if desired.
Tail Length
indicator Mark
Buckle
3
5
7
4
6
NOTE: If alignment of band and shield is
unsatisfactory, tension on band can be
relaxed by pushing on slotted release
lever on top of tool. Make adjustments as
necessaryandagainsqueezeblackpull-up
handle.
NOTE: Prepared Band should have ( ) Mark
visible approximately where shown in Fiꢀure 3.
6. CompletetheClampingProcessbysqueez-
ing the Gray Cut-Off Handle.
7. Removeexcessbandfromtoolanddispose.
ꢈ. inspect Shield Termination.
8
Dimensions in Inches (millimeters) are subject to change without notice.
U.S. CAGE Code 06324
© 2011 Glenair, Inc.
Printed in U.S.A.
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
www.glenair.com
E-Mail: sales@glenair.com
29
QQ：2881495808 复制
