Switching Specifications
(T
A
= 25°C)
Parameter
Propagation
Delay Time to
High Output
Level
Propagation
Delay Time to
Low Output
Level
Rise Time
Sym.
t
PLH
Device
HCPL-3100
HCPL-3101
t
PHL
HCPL-3100
HCPL-3101
t
r
t
f
|CM
H
|
HCPL-3100
HCPL-3101
Fall Time
HCPL-3100
HCPL-3101
Output High
Level Common
Mode Transient
Immunity
Output Low
Level Common
Mode Transient
Immunity
HCPL-3100 1500
HCPL-3101
5000
-
V/µs
-
0.2
0.5
µs
Min.
-
-
-
-
-
Typ.
1
0.3
1
0.3
0.2
Max. Units
2
0.5
2
0.5
0.5
µs
µs
µs
µs
µs
Test Conditions
I
F
= 10 mA
I
F
= 5 mA
I
F
= 10 mA
I
F
= 5 mA
I
F
= 10 mA
I
F
= 5 mA
I
F
= 10 mA
I
F
= 5 mA
I
F
= 10 mA
I
F
= 5mA
V
CM
= 600 V
(peak),
V
CC
= 24 V
V
O1
= 24 V
∆V
02H
=
∆V
02L
= 2.0 V
10
2
V
CC
= 24 V,
V
O1
= 24 V,
R
G
= 47
Ω,
C
G
= 3000 pF
Fig.
9,
25,
26,
27
Note
2, 6
|CM
L
|
1500
5000
-
V/µs
I
F
= 0 mA
Packaging Characteristics
Parameter
Input-Output Momentary
Withstand Voltage*
Resistance (Input-Output)
Capacitance (Input-Output)
Sym.
V
ISO
R
I-O
C
I-O
Min.
5000
5x10
10
–
10
11
1.2
–
–
Typ.
Max.
Units
V rms
Ω
pF
Test Conditions
RH = 40% to 60%
t = 1 min, T
A
= 25°C
V
I-O
= 500 V, T
A
= 25°C
RH = 40% to 60%
f = 1 MHz
Fig.
Note
4, 5
4
4
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output
continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table (if applicable), your
equipment level safety specification, or HP Application Note 1074, “Optocoupler Input-Output Endurance Voltage.”
Notes:
1. Derate absolute maximum ratings with ambient temperatures as shown in Figures 11 and 12.
2. A bypass capacitor of 0.01
µF
or more is needed near the device between V
CC
and GND when measuring output and transfer
characteristics.
3. I
FLH
represents the forward current when the output goes from low to high.
4. Device considered a two terminal device; pins 1-4 are shorted together and pins 5-8 are shorted together.
5. For devices with minimum V
ISO
specified at 5000 V rms, in accordance with UL 1577, each optocoupler is proof-tested by applying an
insulation test voltage
≥
6000 V rms for one second (leakage current detection limit, I
I-O
≤
200
µA).
6. The t
PLH
and t
PHL
propagation delays are measured from the 50% level of the input pulse to the 50% level of the output pulse.
7. R
2
limits the Q1 and Q2 peak currents. For more applications and circuit design information see Application Note “Power Transistor
Gate/Base Drive Optocouplers.”
1-343