欢迎访问ic37.com |
会员登录 免费注册
发布采购

AAT3114 参数 Datasheet PDF下载

AAT3114图片预览
型号: AAT3114
PDF下载: 下载PDF文件 查看货源
内容描述: 高能效1.5x分数电荷泵为白光LED应用 [High Efficiency 1.5X Fractional Charge Pumps For White LED Applications]
分类和应用:
文件页数/大小: 15 页 / 1591 K
品牌: ANALOGICTECH [ ADVANCED ANALOGIC TECHNOLOGIES ]
 浏览型号AAT3114的Datasheet PDF文件第4页浏览型号AAT3114的Datasheet PDF文件第5页浏览型号AAT3114的Datasheet PDF文件第6页浏览型号AAT3114的Datasheet PDF文件第7页浏览型号AAT3114的Datasheet PDF文件第9页浏览型号AAT3114的Datasheet PDF文件第10页浏览型号AAT3114的Datasheet PDF文件第11页浏览型号AAT3114的Datasheet PDF文件第12页  
PRODUCT DATASHEET
AAT3113, AAT3114/14A
ChargePump
TM
High Efficiency 1.5X Fractional Charge Pumps For White LED Applications
Functional Block Diagram
VIN
Soft Start
600kHz
Oscillator
Voltage
Reference
1.5X
Charge
Pump
C1+
C1-
C2+
C2-
OUT
EN/SET
S
2
Cwire
Interface
5
32x8 bit
ROM
8
Current
Mode
DAC
D1
D2
D3
D4
D5*
D6*
GND
* AAT3114/14A only
Functional Description
The AAT3113 and AAT3114/14A devices are high effi-
ciency 1.5X fractional charge pumps intended for white
LED backlight applications. The fractional charge pump
consists of a linear regulator followed by a 1.5X charge
pump. The AAT3113 and AAT3114/14A require only four
external components: two 1µF ceramic capacitors for the
charge pump flying capacitors (C1 and C2), one 1µF
ceramic capacitor for C
IN
, and one 0.33µF to 1µF ceram-
ic capacitor for C
OUT
. The charge pump output is con-
verted into four or six constant current outputs (D1 to
D4 or D6) to drive four or six individual LEDs with a
maximum of 20mA each. The current source output
magnitude is controlled by the EN/SET serial data
S
2
Cwire interface. The interface records rising edges of
the EN/SET pin and decodes them into 32 individual cur-
rent level settings each 1dB apart (see Table 1, Current
Level Settings). Code 32 is full scale, and Code 1 is full
scale attenuated by 31dB. The modulo 32 interface
wraps states back to state 1 after the 32nd clock. With
each EN/SET pulse, the output current increases by 1dB.
To decrease the output current by 1dB, 31 EN/SET clock
pulses are required. The counter can be clocked at
speeds up to 1MHz, so intermediate states are not visi-
ble. The first rising edge of EN/SET enables the IC and
initially sets the output LED current to -31dB, the lowest
setting equal to 525µA. Once the final clock cycle is input
for the desired brightness level, the EN/SET pin is held
high to maintain the device output current at the pro-
grammed level. The device is disabled 500µs after the
EN/SET pin transitions to a logic low state.
8
www.analogictech.com
3113.2008.05.1.10