欢迎访问ic37.com |
会员登录 免费注册
发布采购

AS111PGW10/SPACE 参数 Datasheet PDF下载

AS111PGW10/SPACE图片预览
型号: AS111PGW10/SPACE
PDF下载: 下载PDF文件 查看货源
内容描述: 电压比较器 [Voltage Comparator]
分类和应用: 比较器放大器
文件页数/大小: 22 页 / 1614 K
品牌: AUSTIN [ AUSTIN SEMICONDUCTOR ]
 浏览型号AS111PGW10/SPACE的Datasheet PDF文件第4页浏览型号AS111PGW10/SPACE的Datasheet PDF文件第5页浏览型号AS111PGW10/SPACE的Datasheet PDF文件第6页浏览型号AS111PGW10/SPACE的Datasheet PDF文件第7页浏览型号AS111PGW10/SPACE的Datasheet PDF文件第9页浏览型号AS111PGW10/SPACE的Datasheet PDF文件第10页浏览型号AS111PGW10/SPACE的Datasheet PDF文件第11页浏览型号AS111PGW10/SPACE的Datasheet PDF文件第12页  
Voltage  
Comparator  
AS111 RAD-TOL  
PRELIMINARY SPECIFICATION  
Austin Semiconductor, Inc.  
Electrical Characteristics  
DC PARAMETERS: DRIFT VALUES  
(The following conditions apply to all the following parameters, unless otherwise specified.)  
DC: +Vcc = +15V, Vcm = 0V. "Delta calculations performed on /SPACE devices at group B, subgroup 5  
only".  
PIN-  
NAME  
SUB-  
SYMBOL  
Vio  
PARAMETER  
CONDITIONS  
NOTES  
MIN  
MAX UNIT  
GROUPS  
Input Offset  
Voltage  
Vin = 0V, Rs = 50 Ohms  
-0.5  
-0.5  
0.5  
mV  
mV  
1
1
+Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V,  
Vcm = -14.5V, Rs = 50 Ohms  
0.5  
+Vcc = 2V, -Vcc = -28V, Vin = 0V,  
Vcm = +13V, Rs = 50 Ohms  
-0.5  
0.5  
mV  
1
Iib+  
Iib-  
Icex  
Input Bias  
Current  
Vin = 0V, Rs = 50K Ohms  
-12.5 12.5  
-12.5 12.5  
nA  
nA  
1
1
+Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V,  
Vcm = -14.5V, Rs = 50K Ohms  
+Vcc = 2V, -Vcc = -28V, Vin = 0V,  
Vcm = +13V, Rs = 50K Ohms  
-12.5 12.5  
nA  
1
Input Bias  
Current  
Vin = 0V, Rs = 50K Ohms  
-12.5 12.5  
-12.5 12.5  
nA  
nA  
1
1
+Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V,  
Vcm = -14.5V, Rs = 50K Ohms  
+Vcc = 2V, -Vcc = -28V, Vin = 0V,  
Vcm = +13V, Rs = 50K Ohms  
-12.5 12.5  
nA  
nA  
1
1
Output Leakage  
Current  
+Vcc = 18V, -Vcc = -18V, Vout = 32V  
-5  
5
Note 1: Istb = -2mA at -55 C.  
Note 2: Calculated parameter.  
Note 3: Use DC tape for Ios and Vio(adj), Ave+ and Ave- as indicated in TAPE NAME section of  
this JRETS.  
Note 4: Uses AC tape and hardware.  
Note 5: Actual min. limit used is 5mA due to test setup.  
Note 6: Datalog reading in K = V/mV.  
Note 7: Vid is voltage difference between inputs.  
Note 8: Pre and post irradiation limits are identical to those listed under AC and DC  
electrical characteristics except as listed in the Post Radiation Limits Table. These  
parts may be dose rate sensitive in a space environment and demonstrate enhanced low  
dose rate effect. Radiaton end point limits for the noted parameters are guaranteed  
only for the conditions as specified in MIL-STD-883, Method 1019.5, Condition A.