HCPL-2201, HCPL-2202, HCPL-2211,HCPL-2212,
HCPL-2231, HCPL-2232, HCPL-0201, HCPL-0211,
HCNW2201, HCNW2211
Very High CMR, Wide V
CC
Logic Gate Optocouplers
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
The HCPL-22XX, HCPL-02XX, and HCNW22XX are optical-
ly-coupled logic gates. The HCPL-22XX, and HCPL-02XX
contain a GaAsP LED while the HCNW22XX contains an
AlGaAs LED. The detectors have totem pole output stag-
es and optical receiver input stages with built-in Schmitt
triggers to provide logic-compatible waveforms, eliminat-
ing the need for additional waveshaping.
A superior internal shield on the HCPL-2211/12, HCPL-
0211, HCPL-2232 and HCNW2211 guarantees common
mode transient immunity of 10 kV/µs at a common
mode voltage of 1000 volts.
Features
•
10 kV/µs minimum Common Mode Rejection
(CMR) at V
CM
= 1000 V (HCPL-2211/2212/0211/2232,
HCNW2211)
•
Wide operating V
CC
range: 4.5 to 20 Volts
•
300 ns propagation delay guaranteed over the full
temperature range
•
5 Mbd typical signal rate
•
•
•
•
•
•
Low input current (1.6 mA to 1.8 mA)
Hysteresis
Totem pole output (no pullup resistor required)
Available in 8-Pin DIP, SOIC-8, widebody packages
Guaranteed performance from -40°C to 85°C
Safety approval
– UL recognized -3750 V rms for 1 minute (5000 V
rms for 1 minute for HCNW22XX) per UL1577
– CSAapproved
– IEC/EN/DIN EN 60747-5-2 approved with V
IORM
=
630 V
peak
(HCPL-2211/2212 Option 060 only) and
V
IORM
= 1414 V
peak
(HCNW22XX only)
•
MIL-PRF-38534 hermetic version available
(HCPL-52XX/62XX)
Functional Diagram
HCPL-2201/11
HCPL-0201/11
HCNW2201/11
NC 1
ANODE 2
CATHODE 3
NC 4
8 V
CC
7 V
O
6 NC
5 GND
NC 1
ANODE 2
CATHODE 3
NC 4
HCPL-2202/12
8 V
CC
7 NC
6 V
O
5 GND
SHIELD
HCPL-2231/32
SHIELD
ANODE 1 1
CATHODE 1 2
CATHODE 2 3
ANODE 2 4
8 V
CC
7 V
O1
6 V
O2
5 GND
TRUTH TABLE
(POSITIVE LOGIC)
LED
V
O
ON
HIGH
OFF
LOW
Applications
•
•
•
•
•
•
•
Isolation of high speed logic systems
Computer-peripheral interfaces
Microprocessor system interfaces
Ground loop elimination
Pulse transformer replacement
High speed line receiver
Power control systems
SHIELD
A 0.1 µF bypass capacitor must be connected between pins 5 and 8.
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of
HCPL-2201 Functional Diagram
this component to prevent damage and/or degradation which may be induced by ESD.
AVAGO [ AVAGO TECHNOLOGIES LIMITED ]
