Embossed Carrier Configuration
8 & 12mm Tape Only
P
0
T
2
T
D
0
DEFORMATION
BETWEEN
EMBOSSMENTS
A
0
B
1
TOP COVER
TAPE
F
B
0
E
2
P
2
10 PITCHES CUMULATIVE
TOLERANCE ON TAPE
±0.2mm
(±0.008)
EMBOSSMENT
E
1
W
K
0
S
1
T
1
CENTER LINES
OF CAVITY
P
1
MAX. CAVITY
SIZE - SEE NOTE 1
D
1
FOR COMPONENTS
2.00 mm x 1.20 mm AND
LARGER (0.079 x 0.047)
B
1
IS FOR TAPE READER REFERENCE ONLY
INCLUDING DRAFT CONCENTRIC AROUND B
0
User Direction of Feed
8 & 12mm Embossed Tape
Metric Dimensions Will Govern
CONSTANT DIMENSIONS
Tape Size
8mm
and
12mm
D
0
1.50
+0.10
-0.0
-0.0
(0.059
+0.004
)
E
P
0
P
2
S
1
Min.
0.60
(0.024)
T Max.
0.60
(0.024)
T
1
0.10
(0.004)
Max.
1.75 ± 0.10
4.0 ± 0.10
2.0 ± 0.05
(0.069 ± 0.004) (0.157 ± 0.004) (0.079 ± 0.002)
VARIABLE DIMENSIONS
Tape Size
B
1
Max.
4.35
(0.171)
8.20
(0.323)
4.35
(0.171)
8.20
(0.323)
D
1
Min.
1.00
(0.039)
1.50
(0.059)
1.00
(0.039)
1.50
(0.059)
E
2
Min.
6.25
(0.246)
10.25
(0.404)
6.25
(0.246)
10.25
(0.404)
F
P
1
See Note 5
8mm
3.50 ± 0.05
4.00 ± 0.10
(0.138 ± 0.002) (0.157 ± 0.004)
5.50 ± 0.05
4.00 ± 0.10
(0.217 ± 0.002) (0.157 ± 0.004)
3.50 ± 0.05
2.00 ± 0.10
(0.138 ± 0.002) (0.079 ± 0.004)
5.50 ± 0.05
8.00 ± 0.10
(0.217 ± 0.002) (0.315 ± 0.004)
R
Min.
See Note 2
25.0
(0.984)
30.0
(1.181)
25.0
(0.984)
30.0
(1.181)
T
2
W
Max.
8.30
(0.327)
12.3
(0.484)
8.30
(0.327)
12.3
(0.484)
A
0
B
0
K
0
2.50 Max.
(0.098)
6.50 Max.
(0.256)
2.50 Max.
(0.098)
6.50 Max.
(0.256)
See Note 1
12mm
8mm
1/2 Pitch
12mm
Double
Pitch
See Note 1
See Note 1
See Note 1
NOTES:
1. The cavity defined by A
0
, B
0
, and K
0
shall be configured to provide the following:
Surround the component with sufficient clearance such that:
a) the component does not protrude beyond the sealing plane of the cover tape.
b) the component can be removed from the cavity in a vertical direction without mechanical
restriction, after the cover tape has been removed.
c) rotation of the component is limited to 20º maximum (see Sketches D & E).
d) lateral movement of the component is restricted to 0.5mm maximum (see Sketch F).
2. Tape with or without components shall pass around radius “R” without damage.
3. Bar code labeling (if required) shall be on the side of the reel opposite the round sprocket holes.
Refer to EIA-556.
4. B
1
dimension is a reference dimension for tape feeder clearance only.
5. If P
1
= 2.0mm, the tape may not properly index in all tape feeders.
Top View, Sketch "F"
Component Lateral Movements
0.50mm (0.020)
Maximum
0.50mm (0.020)
Maximum
48
AVX [ AVX CORPORATION ]
