LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
Long life snap-ins, 105C
LXG
@Endurance
with ripple current : 105C 5000 hours
@Non
solvent-proof type
@Pb-free
design
longer life
KMH
?SPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
-40 to +105C
(at 20C, 120Hz)
10 to 100V
dc
P20%
(M)
I=0.02CV or 3mA, whichever is smaller.
(at 20C after 5 minutes)
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
10V 16V 25V 35V 50V 63V 80 & 100V
Rated voltage (V
dc
)
0.60 0.45 0.30 0.25 0.20 0.15
0.15
(at 20C, 120Hz)
tanE (Max.)
Capacitance change : Capacitance at the lowest operating temperature shall not be less than 70% of the 20C value.
Rated voltage (V
dc
)
10V 16V 25V 35V 50V 63V 80 & 100V
Z(-25C)/Z(+20C)
2
2
3
3
4
4
2
(at 120Hz)
Z(-40C)/Z(+20C)
6
6
8
10
15
15
5
The following specifications shall be satisfied when the capacitors are restored to 20C after subjected to DC voltage with rated ripple
current is applied for 5000 hours at 105C.
Capacitance change
[P25%
of the initial value
D.F. (tanE)
[250%
of the initial specified value
Leakage current
[The
initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 500 hours at 105C
without voltage applied.
Capacitance change
[P20%
of the initial value
D.F. (tanE)
[150%
of the initial specified value
Leakage current
[The
initial specified value
Characteristics
Endurance
Shelf Life
?DIMENSIONS
[mm]
@Terminal
Code : VS (F22 to
F35)
: Standard
Sleeve (PET)
FD+1max.
Negative mark
PC board pin-out
FD+1max.
10
@Terminal
Code : LI (F35)
Sleeve (PET)
Negative mark
4.2P0.5
PC board pin-out
2-1.2B6
5P0.5
LP2
4.5P1
14.2P1
Vent
LP2
*
4.0P0.5
2-F2
Vent
*FD=35mm : 3.5P0.5mm
No plastic disk is the standard design
?PART
NUMBERING SYSTEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
E L XG
AAA
VS N
AAA
M
AAA
S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 390MF:391,3300MF:332)
Dummy terminal code
Terminal code (VS, LI)
Voltage code (ex. 10V:100,100V:101)
Series code
Category
Please refer to "A guide to global code (snap-in type)"
?RATED
RIPPLE CURRENT MULTIPLIERS
@Frequency
Multipliers
Frequency (Hz)
10 to 50V
dc
63 to 100V
dc
50
0.95
0.92
120
1.00
1.00
300
1.03
1.07
1k
1.05
1.13
10k
1.08
1.19
50k
1.08
1.20
(1/3)
CAT. No. E1001E