欢迎访问ic37.com |
会员登录 免费注册
发布采购

FTLX3871MCC42 参数 Datasheet PDF下载

FTLX3871MCC42图片预览
型号: FTLX3871MCC42
PDF下载: 下载PDF文件 查看货源
内容描述: [10Gb/s DWDM 80km Multi-Rate SFP Transceiver]
分类和应用:
文件页数/大小: 14 页 / 744 K
品牌: FINISAR [ FINISAR CORPORATION. ]
 浏览型号FTLX3871MCC42的Datasheet PDF文件第1页浏览型号FTLX3871MCC42的Datasheet PDF文件第2页浏览型号FTLX3871MCC42的Datasheet PDF文件第4页浏览型号FTLX3871MCC42的Datasheet PDF文件第5页浏览型号FTLX3871MCC42的Datasheet PDF文件第6页浏览型号FTLX3871MCC42的Datasheet PDF文件第7页浏览型号FTLX3871MCC42的Datasheet PDF文件第8页浏览型号FTLX3871MCC42的Datasheet PDF文件第9页  
FTLX3871MCCxx Product Specification  
I.  
Pin Descriptions  
Pin  
1
2
3
4
5
6
7
Symbol  
Name/Description  
Ref.  
1
2
3
2
2
2
4
VEET  
TFAULT  
TDIS  
SDA  
SCL  
Transmitter Ground  
Transmitter Fault  
Transmitter Disable. Laser output disabled on high or open.  
2-wire Serial Interface Data Line  
2-wire Serial Interface Clock Line  
Module Absent. Grounded within the module  
Rate Select 0.  
MOD_ABS  
RS0  
8
9
RX_LOS  
RS1  
Loss of Signal indication. Logic 0 indicates normal operation.  
Rate Select 1.  
5
4
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
VEER  
VEER  
RD-  
RD+  
VEER  
VCCR  
VCCT  
VEET  
Receiver Ground  
Receiver Ground  
Receiver Inverted DATA out. AC Coupled.  
Receiver Non-inverted DATA out. AC Coupled.  
Receiver Ground  
Receiver Power Supply  
Transmitter Power Supply  
Transmitter Ground  
1
1
1
6
6
1
TD+  
TD-  
VEET  
Transmitter Non-Inverted DATA in. AC Coupled.  
Transmitter Inverted DATA in. AC Coupled.  
Transmitter Ground  
1
Notes:  
1. Circuit ground is internally isolated from chassis ground.  
2. is an open collector/drain output, which should be pulled up with a 4.7k – 10k Ohms resistor on  
T
FAULT  
the host board if intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V. A high  
output indicates a transmitter fault caused by either the TX bias current or the TX output power  
exceeding the preset alarm thresholds. A low output indicates normal operation. In the low state, the  
output is pulled to <0.8V.  
3. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.  
4. Internally pulled down per SFF-8431 Rev 4.1. See Sec. X of this datasheet for the logic table to use for  
the internal CDRs locking modes.  
5. LOS is open collector output. Should be pulled up with 4.7k – 10kon host board to a voltage  
between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.  
6. Internally connected  
VeeT  
20  
19  
18  
17  
16  
15  
14  
13  
12  
11  
VeeT  
1
2
TD-  
TX_Fault  
TX_Disable  
SDA  
TD+  
3
VeeT  
VccT  
VccR  
VeeR  
RD+  
RD-  
4
5
SCL  
Towards  
Bezel  
Towards  
ASIC  
6
MOD_ABS  
RS0  
7
8
RX_LOS  
RS1  
9
VeeR  
VeeR  
10  
Figure 1. Diagram of Host Board Connector Block Pin Numbers and Names.  
Finisar Corporation – September 2015  
Rev. C1  
Page 3