欢迎访问ic37.com |
会员登录 免费注册
发布采购

DS_FT311D 参数 Datasheet PDF下载

DS_FT311D图片预览
型号: DS_FT311D
PDF下载: 下载PDF文件 查看货源
内容描述: 该FT311D是提供访问外设从Android平台上使用USB设备端口专门针对一个全速USB主机。 [The FT311D is a Full Speed USB host specifically targeted at providing access to peripheral hardware from an Android platform with a USB device port.]
分类和应用:
文件页数/大小: 40 页 / 1024 K
品牌: FTDI [ FUTURE TECHNOLOGY DEVICES INTERNATIONAL LTD. ]
 浏览型号DS_FT311D的Datasheet PDF文件第6页浏览型号DS_FT311D的Datasheet PDF文件第7页浏览型号DS_FT311D的Datasheet PDF文件第8页浏览型号DS_FT311D的Datasheet PDF文件第9页浏览型号DS_FT311D的Datasheet PDF文件第11页浏览型号DS_FT311D的Datasheet PDF文件第12页浏览型号DS_FT311D的Datasheet PDF文件第13页浏览型号DS_FT311D的Datasheet PDF文件第14页  
DS_FT311D USB ANDROID HOST IC Datasheet  
Version 1.0  
Document No.: FT_000660 Clearance No.: FTDI# 305  
4
Function Description  
FT311D is FTDIs Android Accessory Mode integrated circuit device or Android Host. The FT311D behaves  
like a bridge between an Android device and the various I/O available. Selection of various modes is  
performed using CNFGx pins.  
4.1 Key Features  
Easy to use Android accessory IC translating the Device port of the android tablet into either GPIO, UART,  
PWM, I2C Master, SPI Slave or SPI Master capabilities  
4.2 Functional Block Descriptions  
The following paragraphs describe each function within FT311D. Please refer to the block diagram shown  
in Figure 2.1.  
4.2.1 Peripheral Interface Modules  
FT311D has six peripheral interface modules available for selection. Full descriptions of each module are  
described in Section 5.  
GPIO - General purpose I/O pins  
UART  
PWM  
I2C Master  
SPI Slave  
SPI Master  
4.2.2 USB Transceivers  
USB transceiver cells provide the physical USB device interface supporting USB 1.1 and USB 2.0  
standards. Low-speed and full-speed USB data rates are supported. The output driver provides +3.3V  
level slew rate control signalling, whilst a differential receiver and two single ended receivers provide USB  
DATA IN, SE0 and USB Reset condition detection. These cells also include integrated internal pull-down  
resistors as required for host mode.  
4.2.3 USB Host  
These blocks handle the parallel-to-serial and serial-to-parallel conversion of the USB physical layer. This  
includes bit stuffing, CRC generation.  
4.3 I/O Peripherals Signal Names  
Peripheral  
Signal Name  
Outputs Inputs  
Description  
GPIO  
gpio  
uart_txd  
uart_rts#  
uart_rxd  
uart_cts#  
uart_tx_active  
pwm  
7
1
1
0
0
0
4
0
1
0
7
0
0
1
1
1
0
1
1
1
General purpose I/O  
Transmit asynchronous data output  
Request to send control output  
Receive asynchronous data input  
Clear to send control input  
UART  
UART active signal (typically used with RS485)  
Pulse width modulation  
PWM  
I2C  
I2c_scl  
I2C bus serial clock line - slave  
I2C bus serial data line - slave  
SPI clock input  
I2c_sda  
SPI Slave  
spi_s_clk  
Copyright © 2012 Future Technology Devices International Limited  
10