欢迎访问ic37.com |
会员登录 免费注册
发布采购

VNCLO-MB1A 参数 Datasheet PDF下载

VNCLO-MB1A图片预览
型号: VNCLO-MB1A
PDF下载: 下载PDF文件 查看货源
内容描述: Vinculo开发模块 [Vinculo Development Module]
分类和应用:
文件页数/大小: 25 页 / 702 K
品牌: FTDI [ FUTURE TECHNOLOGY DEVICES INTERNATIONAL LTD. ]
 浏览型号VNCLO-MB1A的Datasheet PDF文件第12页浏览型号VNCLO-MB1A的Datasheet PDF文件第13页浏览型号VNCLO-MB1A的Datasheet PDF文件第14页浏览型号VNCLO-MB1A的Datasheet PDF文件第15页浏览型号VNCLO-MB1A的Datasheet PDF文件第17页浏览型号VNCLO-MB1A的Datasheet PDF文件第18页浏览型号VNCLO-MB1A的Datasheet PDF文件第19页浏览型号VNCLO-MB1A的Datasheet PDF文件第20页  
Document Reference No.: FT_000327  
Vinculo Development Module Datasheet Version 1.0  
Clearance No.: FTDI#173  
5 Debugger Interface  
The purpose of the debugger interface, J8, is to provide access to the VNC2 silicon/firmware debugger.  
The debug interface can be accessed by connecting a VNC2_Debug_Module to the J8 connector. This  
debug module will give access to the debugger through a USB connection to a PC via the Integrated  
Development Environment (IDE). The IDE is accessed through a GUI to the VNC2 software development  
tool-chain and gives the following debug capabilities through the debugger interface:  
Flash Erase, Write and Program.  
Application debug - application code can have breakpoints, be single stepped and can be halted.  
Detailed internal debug - memory and register read/write access.  
The IDE may be downloaded from http://www.ftdichip.com/Firmware/V2TC/VNC2toolchain.htm  
The Debugger Interface, and how to use it, is further described in the following applications Note  
Vinculum-II Debug Interface Description  
5.1 Signal Description - Debugger Interface  
Table 5.1 shows the signals and pins description for the Debugger Interface pin header J8  
Name  
Pin No.  
Name  
On PCB  
Type  
Description  
DBG  
I/O  
-
Debugger Interface  
IO0  
-
J8-1  
[Key]  
Not connected. Used to make sure that the debug  
module is connected correctly.  
J8-2  
J8-3  
GND  
PWR  
Module ground supply pin  
GND  
Input  
Can be used by an external device to reset the  
VNC2. This pin is also used in combination with  
PROG# and the UART interface to program  
firmware into the VNC2.  
RESET#  
RST#  
J8-4  
This pin is used in combination with the RESET#  
pin and the UART interface to program firmware  
into the VNC2.  
Input  
PROG#  
5V0  
PRG#  
VCC  
J8-5  
J8-6  
PWR Input  
5.0V module supply pin. This pin can be used to  
provide the 5.0V input to the Vinculo from the  
debugger interface when the Vinculo is not  
powered from the USB connector (VBUs) or the  
CN1  
Table 5.1 - Signal Name and Description Debugger Interface  
Note: # defines active low signals.  
Copyright © 2010 Future Technology Devices International Limited  
12