MBM29LV650UE/651UE-90/12
Table 3 MBM29LV650UE/651UE Command Definitions
Fourth Bus
Read/Write
Cycle
Bus
Write
First Bus Second Bus Third Bus
Write Cycle Write Cycle Write Cycle
Fifth Bus
Sixth Bus
Command
Sequence
Write Cycle Write Cycle
Cycles
Req’d
Addr. Data Addr. Data Addr. Data Addr. Data Addr. Data Addr. Data
Read/Reset
Read/Reset
Autoselect
1
3
3
4
6
6
1
1
3
2
XXXh F0h
—
—
—
—
—
RA
—
—
RD
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
XXXh AAh XXXh 55h XXXh F0h
XXXh AAh XXXh 55h XXXh 90h
XXXh AAh XXXh 55h XXXh A0h
Program
PA
PD
Chip Erase
XXXh AAh XXXh 55h XXXh 80h XXXh AAh XXXh 55h XXXh 10h
Sector Erase
Erase Suspend
Erase Resume
Set to Fast Mode
Fast Program *1
XXXh AAh XXXh 55h XXXh 80h XXXh AAh XXXh 55h
SA
—
—
—
—
30h
—
XXXh B0h
XXXh 30h
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
XXXh AAh XXXh 55h XXXh 20h
—
XXXh A0h
PA
PD
—
—
—
—
—
Reset from Fast
Mode *1
2
4
XXXh 90h XXXh F0h
—
—
—
—
—
—
—
—
—
—
Extended Sector
Group Protection
*2
XXXh 60h SPA 60h SPA 40h SPA SD
Query *3
1
3
XXh 98h
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Hi-ROM Entry
XXXh AAh XXXh 55h XXXh 88h
XXXh AAh XXXh 55h XXXh A0h
Hi-ROM
Program *4
4
4
PA
PD
—
—
—
—
—
—
—
—
Hi-ROMExit *4
XXXh AAh XXXh 55h XXXh 90h XXXh 00h
*1: This command is valid while Fast Mode.
*2: This command is valid while RESET = VID.
*3: The valid addresses are A6 to A0.
*4: This command is valid while Hi-ROM mode.
Note:1. Address bits = X = “H” or “L” for all address commands except or Program Address (PA) and Sector Address
(SA).
2.Bus operations are defined in Table 2.
3.RA = Address of the memory location to be read.
PA = Address of the memory location to be programmed. Addresses are latched on the falling edge of
the write pulse.
SA = Addressofthesectortobeerased. ThecombinationofA21, A20, A19, A18, A17,A16, andA15 willuniquely
select any sector.
4.RD = Data read from location RA during read operation.
PD = Data to be programmed at location PA. Data is latched on the falling edge of write pulse.
5.SPA = Sector group address to be protected. Set sector group address (SGA) and (A6, A1, A0) = (0, 1, 0).
SD = Sector group protection verify data. Output 01h at protected sector group addresses and output
00h at unprotected sector group addresses.
6.Both Read/Reset commands are functionally equivalent, resetting the device to the read mode.
9