X25128
ABSOLUTE MAXIMUM RATINGS*
Temperature under Bias ................... –65
°
C to +135
°
C
Storage Temperature........................ –65
°
C to +150
°
C
Voltage on any Pin with
Respect to V
SS
.................................... –1V to +7V
D.C. Output Current ..............................................5mA
Lead Temperature
(Soldering, 10 seconds) .............................. 300
°
C
RECOMMENDED OPERATING CONDITIONS
Temperature
Commercial
Industrial
Military
*COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and the functional operation
of the device at these or any other conditions above
those indicated in the operational sections of this
specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may
affect device reliability.
Supply Voltage
X25128
X25128-2.7
Min.
0°C
–40°C
–55°C
Max.
+70°C
+85°C
+125°C
3091 FM T06.1
Limits
5V
±10%
2.5V to 5.5V
3091 FM T07.2
D.C. OPERATING CHARACTERISTICS
Limits
Symbol
I
CC
I
SB
I
LI
I
LO
V
lL(1)
V
IH(1)
V
OL1
V
OH1
V
OL2
V
OH2
Parameter
V
CC
Supply Current (Active)
V
CC
Supply Current (Standby)
Input Leakage Current
Output Leakage Current
Input LOW Voltage
Input HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
Min.
Max.
5
1
10
10
Units
mA
µ
A
µA
µA
V
V
V
V
V
V
Test Conditions
SCK = V
CC
x 0.1/V
CC
x 0.9 @ 2 MHz,
SO = Open,
CS
= V
SS
CS
= V
CC
, V
IN
= V
SS
or V
CC
V
IN
=
V
SS
to V
CC
V
OUT
=
V
SS
to V
CC
–1
V
CC
x 0.7
V
CC
– 0.8
V
CC
x 0.3
V
CC
+ 0.5
0.4
0.4
V
CC
= 5V, I
OL
= 3mA
V
CC
= 5V, I
OH
= -1.6mA
V
CC
= 3V, I
OL
= 1.5mA
V
CC
= 3V, I
OH
= -0.4mA
V
CC
– 0.3
POWER-UP TIMING
Symbol
t
PUR(3)
t
PUW(3)
Parameter
Power-up to Read Operation
Power-up to Write Operation
Min.
Max.
1
5
Units
ms
ms
3091 FM T09
CAPACITANCE
T
A
= +25
°
C, f = 1MHz, V
CC
= 5V
Symbol
C
OUT(2)
C
IN(2)
Notes:
(1)
(2)
(3)
Test
Output Capacitance (SO)
Input Capacitance (SCK, SI, CS, WP, HOLD)
Max.
8
6
Units
pF
pF
Conditions
V
OUT
= 0V
V
IN
= 0V
3091 FM T10.1
V
IL
min. and V
IH
max. are for reference only and are not tested.
This parameter is periodically sampled and not 100% tested.
t
PUR
and t
PUW
are the delays required from the time V
CC
is stable until the specified operation can be initiated. These
parameters are periodically sampled and not 100% tested.
8
ICMIC [ IC MICROSYSTEMS ]
