HIN202, HIN206, HIN207, HIN208, HIN211, HIN213
Ordering Information
PART NO.
HIN202CB
HIN202CB-T
HIN202CBN
HIN202CBN-T
HIN202CP
HIN202IB
HIN202IBN
HIN206CB
HIN207CA
HIN207CB
TEMP.
RANGE (
o
C)
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
-40 to 85
-40 to 85
0 to 70
0 to 70
0 to 70
PACKAGE
16 Ld SOIC (W)
16 Ld SOIC (W)
Tape and Reel
16 Ld SOIC (N)
16 Ld SOIC (N)
Tape and Reel
16 Ld PDIP
16 Ld SOIC (W)
16 Ld SOIC (N)
24 Ld SOIC
24 Ld SSOP
24 Ld SOIC
PKG.
DWG. #
M16.3
M16.3
HIN208CB
M16.15
M16.15
HIN211CA
E16.3
M16.3
HIN211CB
M16.15
HIN211CB-T
M24.3
M24.209
M24.3
HIN213CA
HIN213CA-T
0 to 70
0 to 70
0 to 70
28 Ld SOIC
Tape and Reel
28 Ld SSOP
28 Ld SSOP
Tape and Reel
M28.3
M28.209
M28.209
0 to 70
28 Ld SOIC
M28.3
HIN211CA-T
0 to 70
0 to 70
28 Ld SSOP
28 Ld SSOP
Tape and Reel
M28.209
M28.209
HIN208CB-T
0 to 70
0 to 70
24 Ld SOIC
24 Ld SOIC
Tape and Reel
M24.3
M24.3
Ordering Information
(Continued)
PART NO.
HIN207CB-T
TEMP.
RANGE (
o
C)
0 to 70
PACKAGE
24 Ld SOIC
Tape and Reel
PKG.
DWG. #
M24.3
Pin Descriptions
PIN
V
CC
V+
V-
GND
C1+
C1-
C2+
C2-
T
IN
T
OUT
R
IN
R
OUT
EN, EN
SD, SD
NC
Power Supply Input 5V
±10%,
(5V
±5%
HIN207).
Internally generated positive supply (+10V nominal).
Internally generated negative supply (-10V nominal).
Ground Lead. Connect to 0V.
External capacitor (+ terminal) is connected to this lead.
External capacitor (- terminal) is connected to this lead.
External capacitor (+ terminal) is connected to this lead.
External capacitor (- terminal) is connected to this lead.
Transmitter Inputs. These leads accept TTL/CMOS levels. An internal 400kΩ pull-up resistor to V
CC
is connected to each lead.
Transmitter Outputs. These are RS-232 levels (nominally
±10V).
Receiver Inputs. These inputs accept RS-232 input levels. An internal 5kΩ pull-down resistor to GND is connected to each input.
Receiver Outputs. These are TTL/CMOS levels.
Receiver enable Input. With EN = 5V (HIN213 EN = 0V), the receiver outputs are placed in a high impedance state.
Shutdown Input. With SD = 5V (HIN213 SD = 0V), the charge pump is disabled, the receiver outputs are in a high impedance state
(except R4 and R5 of HIN213) and the transmitters are shut off.
No Connect. No connections are made to these leads.
FUNCTION
2
INTERSIL [ INTERSIL CORPORATION ]
