X9313
Pin Descriptions
R
H
/V
H
and R
L
/V
L
The high (R
H
/V
H
) and low (R
L
/V
L
) terminals of the X9313
are equivalent to the fixed terminals of a mechanical
potentiometer. The terminology of R
L
/V
L
and R
H
/V
H
references the relative position of the terminal in relation to
wiper movement direction selected by the U/D input and not
the voltage potential on the terminal.
SYMBOL
TABLE 1. PIN NAMES
DESCRIPTION
High terminal
Wiper terminal
Low terminal
Ground
Supply voltage
Up/Down control input
Increment control input
Chip Select control input
R
H
/V
H
R
W
/V
W
RL/VL
V
SS
V
CC
U/D
INC
CS
R
W
/V
W
R
W
/V
w
is the wiper terminal and is equivalent to the movable
terminal of a mechanical potentiometer. The position of the
wiper within the array is determined by the control inputs.
The wiper terminal series resistance is typically 40Ω at V
CC
= 5V.
Principles of Operation
There are three sections of the X9313: the input control,
counter and decode section; the nonvolatile memory; and
the resistor array. The input control section operates just like
an up/down counter. The output of this counter is decoded to
turn on a single electronic switch connecting a point on the
resistor array to the wiper output. Under the proper
conditions the contents of the counter can be stored in
nonvolatile memory and retained for future use. The resistor
array is comprised of 31 individual resistors connected in
series. At either end of the array and between each resistor
is an electronic switch that transfers the potential at that
point to the wiper.
The wiper, when at either fixed terminal, acts like its
mechanical equivalent and does not move beyond the last
position. That is, the counter does not wrap around when
clocked to either extreme.
The electronic switches on the device operate in a “make
before break” mode when the wiper changes tap positions. If
the wiper is moved several positions, multiple taps are
connected to the wiper for t
IW
(INC to V
W
change). The
R
TOTAL
value for the device can temporarily be reduced by
a significant amount if the wiper is moved several positions.
When the device is powered-down, the last wiper position
stored will be maintained in the nonvolatile memory. When
power is restored, the contents of the memory are recalled
and the wiper is set to the value last stored.
Up/Down (U/D)
The U/D input controls the direction of the wiper movement
and whether the counter is incremented or decremented.
Increment (INC)
The INC input is negative-edge triggered. Toggling INC will
move the wiper and either increment or decrement the
counter in the direction indicated by the logic level on the
U/D input.
Chip Select (CS)
The device is selected when the CS input is LOW. The
current counter value is stored in nonvolatile memory when
CS is returned HIGH while the INC input is also HIGH. After
the store operation is complete the X9313 will be placed in
the low power standby mode until the device is selected
once again.
Pin Configuration
8-Lead DIP/SOIC
INC
U/D
R
H
/V
H
V
SS
1
2
3
4
X9313
8
7
6
5
V
CC
CS
R
L
/V
L
R
W
/V
W
8-Lead MSOP
R
H
/V
H
V
SS
R
W
/V
W
R
L
/V
L
1
2
3
4
X9313
8
7
6
5
U/D
INC
V
CC
CS
Instructions and Programming
The INC, U/D and CS inputs control the movement of the
wiper along the resistor array. With CS set LOW the device
is selected and enabled to respond to the U/D and INC
inputs. HIGH to LOW transitions on INC will increment or
decrement (depending on the state of the U/D input) a seven
bit counter. The output of this counter is decoded to select
one of thirty two wiper positions along the resistive array.
The value of the counter is stored in nonvolatile memory
whenever CS transitions HIGH while the INC input is also
HIGH.
4
FN8177.2
September 9, 2005
INTERSIL [ INTERSIL CORPORATION ]
