4.5 Dual SPST Analog Switches in UCSP
ABSOLUTE MAXIMUM RATINGS
(All Voltages Referenced to GND, Unless Otherwise Noted.)
V+, IN_...................................................................-0.3V to +6.0V
COM_, NO_, NC_ (Note 1) ...........................-0.3V to (V+ + 0.3V)
Continuous Current COM_, NO_, NC_ ........................... 100ꢀA
Peak Current COM_, NO_, NC_
ESD Method 3015.7.............................................................>2kV
Operating Teꢀperature Range ...........................-40°C to +85°C
Junction Teꢀperature......................................................+150°C
Storage Teꢀperature Range.............................-65°C to +150°C
Lead Teꢀperature (soldering, 10s) .................................+300°C
Buꢀp Teꢀperature (soldering) (Note 2)
(pulsed at 1ꢀs, 10% duty cycle)................................ 200ꢀA
Continuous Power Dissipation (T = +70°C)
8-Pin µMAX (derate 4.5ꢀW/°C above +70°C).............362ꢀW
9-Buꢀp UCSP (derate 4.7ꢀW/°C above +70°C).........379ꢀW
Infrared (15s) ...............................................................+220°C
Vapor Phase (60s) .......................................................+215°C
A
Note 1: Signals on COM_, NO_, or NC_ exceeding V+ or GND are claꢀped by internal diodes. Liꢀit forward-diode current to ꢀaxi-
ꢀuꢀ current rating.
Note 2: This device is constructed using a unique set of packaging techniques that iꢀpose a liꢀit on the therꢀal profile the device
can be exposed to during board level solder attach and rework. This liꢀit perꢀits only the use of the solder profiles recoꢀ-
ꢀended in the industry standard specification, JEDEC 020A, paragraph 7.6, table 3 for IR/VPR and convection reflow.
Preheating is required. Hand or wave soldering is not allowed.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—Single +3V Supply
(V+ = +2.7V to +3.6V, V = +1.4V, V = +0.5V, T = T
to T
, unless otherwise noted. Typical values are at V+ = +3.0V,
MAX
IH
IL
A
MIN
T
A
= +25°C, unless otherwise noted.) (Notes 3, 4)
PARAMETER
SYMBOL
CONDITIONS
T
MIN
TYP
MAX
UNITS
A
V
,
COM_
, V
Analog Signal Range
0
V+
V
V
NO_ NC_
ANALOG SWITCH
+25°C
to
3.0
0.1
4.5
5
V+ = 2.7V, I
= 10ꢀA;
= 1.5V
COM_
COM_
COM_
On-Resistance (Note 5)
R
ON
T
MIN
V
or V
NO_
NC_
T
MAX
+25°C
0.3
0.4
1.2
1.5
+0.5
+1.5
+0.5
+1.5
+1
On-Resistance Match Between
Channels (Notes 5, 6)
V+ = 2.7V, I
or V
= 10ꢀA;
= 1.5V
R
ON
T
to
MIN
V
NO_
NC_
T
MAX
+25°C
0.6
V+ = 2.7V, I
or V
= 10ꢀA;
On-Resistance Flatness (Note 7)
R
FLAT(ON)
T
to
MIN
V
= 1.0V, 1.5V, 2.0V
NC_
NO_
T
MAX
+25°C
-0.5
-1.5
-0.5
-1.5
-1
+0.01
+0.01
+0.01
40
NO_, NC_ Off-Leakage Current
(Note 8)
I
I
V+ = 3.6V, V
= 0.3V, 3.3V;
NO_(OFF),
COM_
nA
nA
nA
ns
T
to
MIN
V
or V
= 3.3V, 0.3V
NC_(OFF)
NO_
NC_
T
MAX
+25°C
COM_ Off-Leakage Current
(Note 8)
I
V+ = 3.6V, V
= 0.3V, 3.3V;
COM_ (OFF),
COM_
T
to
MIN
I
V
or V
= 3.3V, 0.3V
NC_
COM_ (OFF)
NO_
T
MAX
+25°C
V+ = 3.6V, V
= 0.3V, 3.3V;
COM_
COM_ On-Leakage Current
(Note 8)
I
V
or V
= 0.3V, 3.3V, or
NC_
COM_(ON)
NO_
T
MIN
to
-2
+2
floating
T
MAX
+25°C
80
V
, V
NO_ NC_
= 1.5V;
Turn-On Tiꢀe
t
ON
T
to
MIN
R = 300 , C = 35pF, Figure 1
L
L
100
T
MAX
2
_______________________________________________________________________________________
MAXIM [ MAXIM INTEGRATED PRODUCTS ]
