欢迎访问ic37.com |
会员登录 免费注册
发布采购

MP1484 参数 Datasheet PDF下载

MP1484图片预览
型号: MP1484
PDF下载: 下载PDF文件 查看货源
内容描述: [3A, 18V, 340KHz Synchronous Rectified Step-Down Converter]
分类和应用:
文件页数/大小: 11 页 / 539 K
品牌: MIPS [ MIPS TECHNOLOGIES, INC. ]
 浏览型号MP1484的Datasheet PDF文件第1页浏览型号MP1484的Datasheet PDF文件第2页浏览型号MP1484的Datasheet PDF文件第4页浏览型号MP1484的Datasheet PDF文件第5页浏览型号MP1484的Datasheet PDF文件第6页浏览型号MP1484的Datasheet PDF文件第7页浏览型号MP1484的Datasheet PDF文件第8页浏览型号MP1484的Datasheet PDF文件第9页  
MP1484 – 3A, 18V, 340KHz SYNCHRONOUS RECTIFIED STEP-DOWN CONVERTER
ELECTRICAL CHARACTERISTICS
(continued)
V
IN
= 12V, T
A
= +25°C, unless otherwise noted.
Parameter
EN Lockout Threshold Voltage
EN Lockout Hysterisis
Input Under Voltage Lockout
Threshold
Input Under Voltage Lockout
Threshold Hysteresis
Soft-Start Current
Soft-Start Period
Thermal Shutdown
(4)
Note:
4) Guaranteed by design, not tested.
Symbol Condition
Min
2.2
Typ
2.5
210
4.05
210
Max
2.7
4.40
Units
V
mV
V
mV
µA
ms
°C
V
IN
Rising
3.80
V
SS
= 0V
C
SS
= 0.1µF
6
15
160
PIN FUNCTIONS
Pin #
1
2
3
4
5
Name
BS
IN
SW
GND
FB
Description
High-Side Gate Drive Boost Input. BS supplies the drive for the high-side N-Channel MOSFET
switch. Connect a 0.01µF or greater capacitor from SW to BS to power the high side switch.
Power Input. IN supplies the power to the IC, as well as the step-down converter switches.
Drive IN with a 4.75V to 18V power source. See
Input Capacitor.
Power Switching Output. SW is the switching node that supplies power to the output. Connect
the output LC filter from SW to the output load. Note that a capacitor is required from SW to
BS to power the high-side switch.
Ground (Connect the exposed pad to Pin 4).
Feedback Input. FB senses the output voltage and regulates it. Drive FB with a resistive
voltage divider connected to it from the output voltage. The feedback threshold is 0.925V. See
Setting the Output Voltage.
Compensation Node. COMP is used to compensate the regulation control loop. Connect a
series RC network from COMP to GND. In some cases, an additional capacitor from COMP to
GND is required. See
Compensation Components.
Enable Input. EN is a digital input that turns the regulator on or off. Drive EN high to turn on
the regulator; low to turn it off. Attach to IN with a 100kΩ pull up resistor for automatic startup.
Soft-Start Control Input. SS controls the soft-start period. Connect a capacitor from SS to GND
to set the soft-start period. A 0.1µF capacitor sets the soft-start period to 15ms. To disable the
soft-start feature, leave SS unconnected.
6
7
8
COMP
EN
SS
MP1484 Rev. 0.9
10/20/2008
www.MonolithicPower.com
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2008 MPS. All Rights Reserved.
3
2008120908500031