LMC660
AC Electrical Characteristics
Parameter
(Continued)
Unless otherwise specified, all limits guaranteed for T
J
= 25˚C.
Boldface
limits apply at the temperature extremes. V
+
=
5V, V
−
= 0V, V
CM
= 1.5V, V
O
= 2.5V and R
L
>
1M unless otherwise specified.
Conditions
Typ
(Note 4)
LMC660AI
Limit
(Note 4)
Total Harmonic Distortion
F = 10 kHz,
A
V
= −10
R
L
= 2 kΩ,
V
O
= 8 V
PP
V
+
= 15V
0.01
LMC660C
Limit
(Note 4)
%
Units
Note 1:
Applies to both single supply and split supply operation. Continuous short circuit operation at elevated ambient temperature and/or multiple Op Amp shorts
can result in exceeding the maximum allowed junction temperature of 150˚C. Output currents in excess of
±
30 mA over long term may adversely affect reliability.
Note 2:
The maximum power dissipation is a function of T
J(max)
,
θ
JA
, and T
A
. The maximum allowable power dissipation at any ambient temperature is P
D
= (T
J(max)
− T
A
)/θ
JA
.
Note 3:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is in-
tended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The
guaranteed specifications apply only for the test conditions listed.
Note 4:
Typical values represent the most likely parametric norm. Limits are guaranteed by testing or correlation.
Note 5:
V
+
= 15V, V
CM
= 7.5V and R
L
connected to 7.5V. For Sourcing tests, 7.5V
≤
V
O
≤
11.5V. For Sinking tests, 2.5V
≤
V
O
≤
7.5V.
Note 6:
V
+
= 15V. Connected as Voltage Follower with 10V step input. Number specified is the slower of the positive and negative slew rates.
Note 7:
Input referred. V
+
= 15V and R
L
= 10 kΩ connected to V
+
/2. Each amp excited in turn with 1 kHz to produce V
O
= 13 V
PP
.
Note 8:
Human body model, 1.5 kΩ in series with 100 pF.
Note 9:
A military RETS electrical test specification is available on request. At the time of printing, the LMC660AMJ/883 RETS spec complied fully with the
boldface
limits in this column. The LMC660AMJ/883 may also be procured to a Standard Military Drawing specification.
Note 10:
For operating at elevated temperatures the device must be derated based on the thermal resistance
θ
JA
with P
D
= (T
J
− T
A
)/θ
JA
.
Note 11:
All numbers apply for packages soldered directly into a PC board.
Note 12:
Do not connect output to V
+
when V
+
is greater than 13V or reliability may be adversely affected.
Typical Performance Characteristics
Supply Current
vs Supply Voltage
Offset Voltage
V
S
=
±
7.5V, T
A
= 25˚C unless otherwise specified
Input Bias Current
DS008767-25
DS008767-24
DS008767-26
Output Characteristics
Current Sinking
Output Characteristics
Current Sourcing
Input Voltage Noise
vs Frequency
DS008767-27
DS008767-28
DS008767-29
www.national.com
4
NSC [ NATIONAL SEMICONDUCTOR ]
