Specifications
■
Characteristics
Operating speed
Operating frequency
Insulation resistance
Contact resistance
0.1 mm to 1 m/second (pin plunger models)
Mechanical: 400 operations per minute max.
Electrical: 30 operations per minute max.
100 MΩ
153 gf:
51 gf:
Dielectric strength (See note 2)
SSG-5 models
SSG-01 models:
SSG-5 models:
SSG-01 models
:
30 mΩ max.
50 mΩ max.
50 mΩ max.
100 mΩ max.
1,000
VAC
(600
VAC
for SSG-01H and SSG-01T), 50/60 Hz for 1 minute between contacts of same polarity
1,500
VAC,
50/60 Hz for 1 minute between each terminal and ground and between each terminal and
non-current-carrying metal parts
Malfunction: 10 to 2,000 Hz, 196 m/s
2
(Approx. 20G)
Malfunction: 490 m/s
2
(approx. 50G) max.
IEC IP40
Class I
175
-25° to 125°C (at 60% RH max.) with no icing
85% max. (for 5°C to 35°C)
Mechanical: 10 million operations min. at 60 operations per minute
Electrical: 200,000 operations min. at 30 operations per minute
Approx. 1.6 g pin plunger type
Vibration resistance (see note 3)
Shock resistance (see note 3)
Degree of protection
Degree of protection against
electric shock
Proof tracking index (PTI)
Ambient operating temperature
Ambient operating humidity
Service life
Weight
Note: 1.
Data shown are of initial value.
2.
The dielectric strength values shown is measured using a separator between the switch and metal mounting plate.
3.
For pin plunger models, the above values apply for use at the free position and total travel position. For the lever models, the values apply
at the total travel position with contact separation = 10μs max.
■
Ratings
General Ratings
Resistive load
Rated
voltage
125
VAC
250
VAC
8
VDC
14
VDC
30
VDC
125
VDC
250
VDC
Note: 1.
2.
3.
4.
5.
6.
7.
NC
5 A (0.1 A)
3A
5A
5A
4 A(0.1 A)
0.4 A
0.2 A
NO
NC
1.5 A
1A
2A
2A
2A
0.05 A
0.03 A
Lamp load
NO
0.7 A
0.5 A
Inductive load
NC
3A
2A
5A
4A
3A
0.4 A
0.2 A
NO
NC
2.5 A
1.5 A
3A
3A
3A
0.05 A
0.05 A
Motor load
NO
1.3 A
0.8 A
The values in the parentheses are for the SSG-01.
The above current ratings are the values of the steady-state current.
Inductive load has a power factor of 0.7 min. (AC) and a time constant of 7 ms max. (DC).
Lamp load has an inrush current of 10 times the steady-state current.
Motor load has an inrush current of 6 times the steady-state current.
If the Switch is used in a DC circuit and is subjected to a surge current, connect a surge suppressor across the switch.
The electrical rating applies under the following test conditions:
Ambient Temperature = 20±2°C, Ambient Humidity = 65±5%, Operating frequency = 30 operations/minute
110
Subminiature Basic Switch
SSG
OMRON [ OMRON ELECTRONICS LLC ]
