欢迎访问ic37.com |
会员登录 免费注册
发布采购

CAT4201TD-GT3 参数 Datasheet PDF下载

CAT4201TD-GT3图片预览
型号: CAT4201TD-GT3
PDF下载: 下载PDF文件 查看货源
内容描述: 350毫安高效率降压LED驱动器 [350 mA High Efficiency Step Down LED Driver]
分类和应用: 显示驱动器驱动程序和接口接口集成电路光电二极管PC
文件页数/大小: 13 页 / 181 K
品牌: ONSEMI [ ON SEMICONDUCTOR ]
 浏览型号CAT4201TD-GT3的Datasheet PDF文件第5页浏览型号CAT4201TD-GT3的Datasheet PDF文件第6页浏览型号CAT4201TD-GT3的Datasheet PDF文件第7页浏览型号CAT4201TD-GT3的Datasheet PDF文件第8页浏览型号CAT4201TD-GT3的Datasheet PDF文件第9页浏览型号CAT4201TD-GT3的Datasheet PDF文件第11页浏览型号CAT4201TD-GT3的Datasheet PDF文件第12页浏览型号CAT4201TD-GT3的Datasheet PDF文件第13页  
CAT4201
300
250
LED CURRENT [mA]
200
150
100
50
0
100
80
60
40
DUTY CYCLE [%]
20
0
Operation from High Supply Voltage Above 14 V
For operation from a supply voltage above 14 V, it is
recommended to have a slew rate of 1
ms
or more for every
5 V increase in VBAT supply. When using a high supply
voltage of 24 V, a 1
W
or 2
W
resistor in series with the supply,
as shown on Figure 28, is recommended to limit the slew rate
of the supply voltage. A 4.7
mF
minimum ceramic capacitor
is placed between the VBAT pin and ground. The
combination of the series resistor R3 and input capacitor C1
acts as a low pass filter limiting the excessive in−rush
currents and overvoltage transients which would otherwise
occur during “hot−plug” conditions, thereby protecting the
CAT4201 driver.
VBAT R3
24 V 1
W
C1
4.7
mF
VBAT
CAT4201
RSET
CTRL SW
GND
R1
1 kW
D1
C2
4.7
mF
L
33
mH
300 mA
Figure 25. LED Current vs. Duty Cycle
VBAT
12 V
C1
VBAT
CAT4201
RSET
CTRL
SW
GND
D
C2
10
mF
L
22
mH
R2
R4
1 kW
R5
47 kW
1 kW
Q1
NPN
4.7
mF
R1
10 kW
R1
10 kW
Figure 28. 24 V Application with 5 LEDs
Operation from High Supply Voltage of 36 V
5V
0V
PWM
control
When powering from a high supply voltage of 36 V, a 2
W
resistor in series with the supply is recommended, as shown
on Figure 29, to limit the slew rate of the supply voltage.
VBAT R3
36 V 2
W
C1
4.7
mF
VBAT
CAT4201
RSET
CTRL SW
GND
R2
1 kW
D1
C2
2.2
mF
L
47
mH
300 mA
Figure 26. Circuit for PWM on CTRL
PWM on RSET Pin
Another dimming method is to place in parallel to R1
another resistor with a FET in series, as shown on Figure 27.
R1 sets the minimum LED current corresponding to 0% duty
cycle. The combined resistor of R1 and Rmax sets the
maximum LED current corresponding to 100% duty cycle.
VBAT
13 V C1
4.7
mF
VBAT
CAT4201
RSET
R1
CTRL
SW
GND
D
C2
10
mF
L
22
mH
R2
OFF ON
1 kW
Q1
NPN
R1
10 kW
Figure 29. 36 V Application with 6 LEDs
Parallel Configuration for Driving LEDs Beyond
350 mA
Rmax
PWM
control
Figure 27. Circuit for PWM on RSET
A resistor value for R1 of less than 90 kW is recommended
to provide better accuracy.
Several CAT4201 devices can be connected in parallel for
driving LEDs with current in excess of 350 mA. The
CAT4201 driver circuits are connected to the same LED
cathode. Figure 30 shows the application schematic for
driving 1 A into one LED with three CAT4201 connected in
parallel. Each CAT4201 is driving the LED with a current set
by its RSET resistor. The resulting LED current is equal to
the sum of each driver current.
http://onsemi.com
10