LM393, LM393A, LM293, LM2903, LM2903V
MAXIMUM RATINGS
Rating
Power Supply Voltage
Input Differential Voltage Range
Input Common Mode Voltage Range
Output Short Circuit–to–Ground
Output Sink Current (Note 1)
Power Dissipation @ TA = 25°C
Derate above 25°C
Operating Ambient Temperature Range
LM293
LM393, 393A
LM2903
LM2903V
Maximum Operating Junction Temperature
LM393, 393A, 2903, LM2903V
LM293
Storage Temperature Range
Symbol
VCC
VIDR
VICR
ISC
ISink
PD
1/R
θJA
TA
–25 to +85
0 to +70
–40 to +105
–40 to +125
TJ(max)
125
150
Tstg
–65 to +150
°C
°C
Value
+36 or
±18
36
–0.3 to +36
Continuous
20
570
5.7
Unit
Vdc
Vdc
Vdc
mA
mW
mW/°C
°C
ELECTRICAL CHARACTERISTICS
(VCC = 5.0 Vdc, Tlow
≤
TA
≤
Thigh,* unless otherwise noted.)
LM393A
Characteristic
Ch
i i
Input Offset Voltage (Note 2)
TA = 25°C
Tlow
≤
TA
≤
Thigh
Input Offset Current
TA = 25°C
Tlow
≤
TA
≤
Thigh
Input Bias Current (Note 3)
TA = 25°C
Tlow
≤
TA
≤
Thigh
Input Common Mode Voltage Range (Note 4)
TA = 25°C
Tlow
≤
TA
≤
Thigh
Voltage Gain RL
≥
15 kΩ, VCC = 15 Vdc, TA = 25°C
Large Signal Response Time
Vin = TTL Logic Swing, Vref = 1.4 Vdc
VRL = 5.0 Vdc, RL = 5.1 kΩ, TA = 25°C
Response Time (Note 5) VRL = 5.0 Vdc, RL = 5.1 kΩ, TA = 25°C
Input Differential Voltage (Note 6)
All Vin
≥
Gnd or V– Supply (if used)
Output Sink Current
Vin
≥
1.0 Vdc, Vin+ = 0 Vdc, VO
≤
1.5 Vdc, TA = 25°C
Output Saturation Voltage
Vin
≥
1.0 Vdc, Vin+ = 0 Vdc, ISink
≤
4.0 mA, TA = 25°C
Tlow
≤
TA
≤
Thigh
* Tlow = 0°C, Thigh = +70°C for LM393/393A
NOTES:
1. The maximum output current may be as high as 20 mA, independent of the magnitude of VCC, output short circuits to VCC can cause excessive
heating and eventual destruction.
2. At output switch point, VO 1.4 Vdc, RS = 0
Ω
with VCC from 5.0 Vdc to 30 Vdc, and over the full input common mode range (0 V to VCC = –1.5 V).
3. Due to the PNP transistor inputs, bias current will flow out of the inputs. This current is essentially constant, independent of the output state, there
fore, no loading changes will exist on the input lines.
4. Input common mode of either input should not be permitted to go more than 0.3 V negative of ground or minus supply. The upper limit of common
mode range is VCC –1.5 V.
5. Response time is specified with a 100 mV step and 5.0 mV of overdrive. With larger magnitudes of overdrive faster response times are obtainable.
6. The comparator will exhibit proper output state if one of the inputs becomes greater than VCC, the other input must remain within the common mode
range. The low input state must not be less than –0.3 V of ground or minus supply.
Symbol
S b l
VIO
Min
–
–
Typ
±1.0
–
±50
–
25
–
–
–
200
300
Max
±2.0
4.0
Unit
U i
mV
IIO
–
–
IIB
–
–
VICR
0
0
AVOL
–
50
–
nA
±50
±150
nA
250
400
V
VCC –1.5
VCC –2.0
–
–
V/mV
ns
tTLH
VID
ISink
VOL
–
–
6.0
1.3
–
16
–
VCC
–
µs
V
mA
mV
–
–
150
–
400
700
]
2
MOTOROLA ANALOG IC DEVICE DATA
ONSEMI [ ON SEMICONDUCTOR ]
