MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Dual 3-Input 3-Output NOR
Gate
The MC10H211 is designed to drive up to six transmission lines simultan–
eously. The multiple outputs of this device also allow the wire “OR”–ing of
several levels of gating for minimization of gate and package count.
The ability to control three parallel lines with minimum propagation delay
from a single point makes the MC10H211 particularly useful in clock distribution
applications where minimum clock skew is desired.
•
Propagation Delay, 1.0 ns Typical
•
Power Dissipation, 160 mW Typical
•
Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range)
•
Voltage Compensated
•
MECL 10K–Compatible
MAXIMUM RATINGS
Characteristic
Power Supply (VCC = 0)
Input Voltage (VCC = 0)
Output Current — Continuous
— Surge
Operating Temperature Range
Storage Temperature Range — Plastic
— Ceramic
Symbol
VEE
VI
Iout
TA
Tstg
Rating
–8.0 to 0
0 to VEE
50
100
0 to +75
–55 to +150
–55 to +165
Unit
Vdc
Vdc
mA
°C
°C
°C
MC10H211
L SUFFIX
CERAMIC PACKAGE
CASE 620–10
P SUFFIX
PLASTIC PACKAGE
CASE 648–08
FN SUFFIX
PLCC
CASE 775–02
LOGIC DIAGRAM
2
5
6
7
3
4
12
9
10
11
13
14
ELECTRICAL CHARACTERISTICS
(VEE = –5.2 V
±5%)
(See Note)
0°
Characteristic
Power Supply Current
Input Current High
Input Current Low
High Output Voltage
Low Output Voltage
High Input Voltage
Low Input Voltage
Symbol
IE
IinH
IinL
VOH
VOL
VIH
VIL
tpd
tr
tf
Min
—
—
0.5
Max
42
720
—
Min
—
—
0.5
25°
Max
38
450
—
Min
—
—
0.3
75°
Max
42
450
—
–0.735
–1.60
–0.735
–1.45
Unit
mA
µA
µA
Vdc
Vdc
Vdc
Vdc
VCC1
AOUT
AOUT
AOUT
AIN
AIN
AIN
VEE
VCC1 = PINS 1, 15
VCC2 = PIN 16
VEE = PIN 8
–1.02 –0.84 –0.98 –0.81 –0.92
–1.95 –1.63 –1.95 –1.63 –1.95
–1.17 –0.84 –1.13 –0.81 –1.07
–1.95 –1.48 –1.95 –1.48 –1.95
DIP
PIN ASSIGNMENT
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
VCC2
VCC1
BOUT
BOUT
BOUT
BIN
BIN
BIN
AC PARAMETERS
Propagation Delay
Rise Time
Fall Time
0.7
0.9
0.9
1.6
2.0
2.0
0.7
0.9
0.9
1.6
2.2
2.2
0.7
0.9
0.9
1.7
2.4
2.4
ns
ns
ns
NOTE:
Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed
circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated
through a 50–ohm resistor to –2.0 volts.
Note:
If crosstalk is present, double bypass capacitor to 0.2
µF.
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
3/93
©
Motorola, Inc. 1996
2–296
REV 5
ONSEMI [ ON SEMICONDUCTOR ]
