欢迎访问ic37.com |
会员登录 免费注册
发布采购

NCP1011AP065 参数 Datasheet PDF下载

NCP1011AP065图片预览
型号: NCP1011AP065
PDF下载: 下载PDF文件 查看货源
内容描述: 自供电单片开关器,用于低待机功耗离线SMPS [Self−Supplied Monolithic Switcher for Low Standby−Power Offline SMPS]
分类和应用: 开关
文件页数/大小: 24 页 / 476 K
品牌: ONSEMI [ ON SEMICONDUCTOR ]
 浏览型号NCP1011AP065的Datasheet PDF文件第2页浏览型号NCP1011AP065的Datasheet PDF文件第3页浏览型号NCP1011AP065的Datasheet PDF文件第4页浏览型号NCP1011AP065的Datasheet PDF文件第5页浏览型号NCP1011AP065的Datasheet PDF文件第6页浏览型号NCP1011AP065的Datasheet PDF文件第7页浏览型号NCP1011AP065的Datasheet PDF文件第8页浏览型号NCP1011AP065的Datasheet PDF文件第9页  
NCP1010, NCP1011,
NCP1012, NCP1013,
NCP1014
Self−Supplied Monolithic
Switcher for Low Standby−
Power Offline SMPS
The NCP101X series integrates a fixed−frequency current−mode
controller and a 700 V MOSFET. Housed in a PDIP−7,
PDIP−7 Gull Wing, or SOT−223 package, the NCP101X offers
everything needed to build a rugged and low−cost power supply,
including soft−start, frequency jittering, short−circuit protection,
skip−cycle, a maximum peak current setpoint and a Dynamic
Self−Supply (no need for an auxiliary winding).
Unlike other monolithic solutions, the NCP101X is quiet by nature:
during nominal load operation, the part switches at one of the available
frequencies (65
100
130 kHz). When the current setpoint falls
below a given value, e.g. the output power demand diminishes, the IC
automatically enters the so−called skip−cycle mode and provides
excellent efficiency at light loads. Because this occurs at typically 1/4
of the maximum peak value, no acoustic noise takes place. As a result,
standby power is reduced to the minimum without acoustic noise
generation.
Short−circuit detection takes place when the feedback signal fades
away, e.g. in true short−circuit conditions or in broken Optocoupler
cases. External disabling is easily done either simply by pulling the
feedback pin down or latching it to ground through an inexpensive
SCR for complete latched−off. Finally soft−start and frequency
jittering further ease the designer task to quickly develop low−cost and
robust offline power supplies.
For improved standby performance, the connection of an auxiliary
winding stops the DSS operation and helps to consume less than
100 mW at high line. In this mode, a built−in latched overvoltage
protection prevents from lethal voltage runaways in case the
Optocoupler would brake. These devices are available in economical
8−pin dual−in−line and 4−pin SOT−223 packages.
Features
4
1
http://onsemi.com
MARKING DIAGRAMS
4
SOT−223
CASE 318E
ST SUFFIX
1
PDIP−7
CASE 626A
AP SUFFIX
1
PDIP−7
(Gull Wing)
CASE 626AA
APL SUFFIX
1
1
P101xAPyy
AWL
YYWWG
AYW
101xy
G
G
8
1
x
y
1xAPLyyy
AWL
YYWWG
= Current Limit (0, 1, 2, 3, 4)
= Oscillator Frequency
A (65 kHz), B (100 kHz), C (130 kHz)
yy
= 06 (65 kHz), 10 (100 kHz), 13 (130 kHz)
yyy
= 065, 100, 130
A
= Assembly Location
WL, L = Wafer Lot
YY, Y = Year
WW, W = Work Week
G
or G = Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 21 of this data sheet.
Built−in 700 V MOSFET with Typical R
DSon
of 11
W
and 22
W
Large Creepage Distance Between High−Voltage Pins
Current−Mode Fixed Frequency Operation:
65 kHz – 100 kHz
130 kHz
Skip−Cycle Operation at Low Peak Currents Only:
No Acoustic Noise!
Dynamic Self−Supply, No Need for an Auxiliary
Winding
Internal 1.0 ms Soft−Start
Latched Overvoltage Protection with Auxiliary
Winding Operation
Frequency Jittering for Better EMI Signature
Auto−Recovery Internal Output Short−Circuit
Protection
Below 100 mW Standby Power if Auxiliary Winding
is Used
Internal Temperature Shutdown
Direct Optocoupler Connection
SPICE Models Available for TRANsient Analysis
Pb−Free Packages are Available
Typical Applications
Low Power AC/DC Adapters for Chargers
Auxiliary Power Supplies (USB, Appliances,TVs, etc.)
©
Semiconductor Components Industries, LLC, 2006
October, 2006
Rev. 17
1
Publication Order Number:
NCP1010/D