DATA SHEET
GBU10A~GBU10K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE - 50 to 800 Volts CURRENT - 10.0 Amperes
FEATURES
.310(7.90)
.290(7.40)
GBU
.880(22.3)
.860(21.8)
.160(4.1)
.140(3.5)
.080(2.03)
.060(1.52)
.740(18.8)
.720(18.3)
Unit: inch ( mm )
• Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
• Ideal for printed circuit board
• Reliable low cost construction utilizing molded plastic technique
• Surge overload rating: 200 Amperes peak
• High temperature soldering guaranteed:
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
.140(3.56)
.130(3.30)
.085(2.16)
.065(1.65)
MECHANICAL DATA
Case: Reliable low cost construction utilizing
molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
.100(2.54)
.085(2.16)
.080(2.03)
.065(1.65)
.190(4.83)
.210(5.33)
.075(1.90)R
.710(18.0)
.690(17.5)
.040(1.02)
.030(0.76)
.022(0.56)
.018(0.46)
.050(1.27)
.040(1.02)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
GBU10A
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Input Voltage
Maximum DC Blocking Voltage
Maximum Average Forward T
C
=100°C
Rectified Output Current at
I2t Rating for fusing ( t<8.35ms)
Peak Forward Surge Current single sine-wave superimposed on
rated load(JEDEC method)
Maximum Instantaneous Forward Voltage Drop per element at 5.0A
Maximum Reverse Leakage at rated T
A
=25°
CDc Blocking Voltage per element T
C
=100°C
Typical Thermal Resistance per leg(Note 2) RθJA
Typical Thermal Resistance per leg(Note 3) RθJC
Operating and Storage Temperature Range, T
J
,TSTG
50
35
50
GBU10B
100
70
100
GBU10D
200
140
200
10.0
GBU10G
400
280
400
GBU10J
600
420
600
GBU10K
800
560
800
UNIT
V
V
V
A
127
200
1.0
5.0
500
8.6
3.1
-55+150
A
2
sec
Apk
Vpk
µA
µA
°C / W
°C / W
°C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
DATE : AUG.29.2002
PAGE . 1
PANJIT [ PAN JIT INTERNATIONAL INC. ]
