Features
DATASHEET
RX630 Group
Renesas MCUs
R01DS0060EJ0100
Rev.1.00
Sep 13, 2011
100-MHz 32-bit RX MCU, on-chip FPU, 165 DMIPS,
up to 2-MB flash memory, USB 2.0 full-speed function interface,
CAN, 10- & 12-bit A/D converter, RTC, up to 22 comms interfaces
Features
■
32-bit RX CPU core
Max. operating frequency: 100 MHz
Capable of 165 DMIPS in operation at 100 MHz
Single precision 32-bit IEEE-754 floating point
Two types of multiply-and-accumulation unit (between memories
and between registers)
32-bit multiplier (fastest instruction execution takes one CPU
clock cycle)
Divider (fastest instruction execution takes two CPU clock cycles)
Fast interrupt
CISC Harvard architecture with 5-stage pipeline
Variable-length instructions: Ultra-compact code
Supports the memory protection unit (MPU)
JTAG and FINE (two-line) debugging interfaces
PLQP0176KB-A
PLQP0144KA-A
PLQP0100KB-A
PLQP0080KB-A
24 × 24 mm, 0.5-mm pitch
20 × 20 mm, 0.5-mm pitch
14 × 14 mm, 0.5-mm pitch
12 × 12 mm, 0.5-mm pitch
PTLG0177JB-A 8 × 8 mm, 0.5-mm pitch
PTLG0145KA-A 7 × 7 mm, 0.5-mm pitch
PTLG0100KA-A 5.5 × 5.5 mm, 0.5-mm pitch
■
Low-power design and architecture
Operation from a single 2.7- to 3.6-V supply
Low power consumption: A product that supports all peripheral
functions draws only 500
μA/MHz.
RTC is capable of operation from a dedicated power supply (min.
operating voltage: 2.3 V).
Four low-power modes
PLBG0176GA-A 13 × 13 mm, 0.8-mm pitch
■
Up to 22 communications interfaces
USB 2.0 full-speed function interface (1 channel)
CAN (compliant with ISO11898-1), incorporating 32 mailboxes
(up to 3 channels)
SCI with multiple functionalities (up to 13 channels)
Choose from among asynchronous mode, clock-synchronous
mode, smart-card interface mode, simple SPI, simple I
2
C, and
extended serial mode.
I
2
C bus interface for transfer at up to 1 Mbps (up to 4 channels)
RSPI for high-speed transfer (up to 3 channels)
■
On-chip main flash memory, no wait states
100-MHz operation, 10-ns read cycle (no wait states)
384-Kbyte to 2-Mbyte capacities
User code programmable via the USB, SCI, or JTAG
■
On-chip data flash memory
Max. 32 Kbytes, reprogrammable up to 100,000 times
Programming/erasing as background operations (BGOs)
■
External address space
8 CS areas (8 × 16 Mbytes)
Multiplexed address data or separate address lines are selectable
per area.
8-, 16-, or 32-bit bus space is selectable per area
■
On-chip SRAM, no wait states
32- to 128-Kbyte capacities
For instructions and operands
Can provide backup on deep software standby
■
DMA
DMAC: Incorporates four channels
DTC
■
Up to 20 extended-function timers
16-bit MTU2: input capture, output capture, complementary PWM
output, phase-counting mode (6 channels)
16-bit TPU: input capture, output capture, phase-counting mode
(12 channels)
8-bit TMR (4 channels)
16-bit compare-match timers (4 channels)
■
Reset and supply management
Power-on reset (POR)
Low voltage detection (LVD) with voltage settings
■
Clock functions
External crystal oscillator or internal PLL for operation at 4 to 16
MHz
Internal 125-kHz LOCO and 50-MHz HOCO
Dedicated 125-kHz LOCO for the IWDT
Frequency of the oscillator for sub-clock generation: 32 kHz
■
A/D converter for 1-MHz Operation
Up to 21 12-bit channels, and incorporating 1 sample-and-hold
circuit
Up to 8 10-bit channels, and incorporating 1 sample-and-hold
circuit
Addition of results of A/D conversion (in the 12-bit A/D converter)
Self diagnosis (for the 10-bit A/D converter)
■
Real-time clock
Adjustment functions (30 seconds, leap year, and error)
Time capture function
(for capturing times in response to event-signal input on external
pins)
■
10-bit D/A converter: 2 channels
■
Temperature sensor for measuring temperature
within the chip
■
Register write protection function can protect
values in important registers against overwriting.
■
Up to 148 pins for GPIO
5-V tolerance, open drain, input pull-up, switchable driving ability
■
Independent watchdog timer
125-kHz LOCO clock operation
■
Useful functions for IEC60730 compliance
Oscillation-stop detection, frequency measurement, CRC, IWDT,
self-diagnostic function for the A/D converter, etc.
■
Operating temp. range
–40
C
to +85C
R01DS0060EJ0100 Rev.1.00
Sep 13, 2011
Page 1 of 168
RENESAS [ RENESAS TECHNOLOGY CORP ]
