9000 Series /
Molded SIP Reed Relays
Model Number
Parameters
COIL SPECS.
Nom. Coil Voltage
Max. Coil Voltage
Coil Resistance
Operate Voltage
Release Voltage
CONTACT RATINGS
Switching Voltage
Switching Current
Carry Current
Contact Rating
1
Life Expectancy-Typical
Static Contact
Resistance (max. init.)
Dynamic Contact
Resistance (max. init.)
RELAY SPECIFICATIONS
Insulation Resistance
(minimum)
Capacitance - Typical
Across Open Contacts
Open Contact to Coil
9001
Test Conditions
Units
VDC
VDC
Ω
VDC - Max.
VDC - Min.
Volts
Amps
Amps
Watts
6
x 10 Ops.
Ω
Ω
2
9002
2
9091
2
4 Pin SIP
5
6.5
500
3.75
0.4
12
15.0
1000
9.0
1.0
200
0.5
1.5
10
1000
0.150
0.200
6 Pin SIP
5
6.5
350
3.75
0.4
12
15.0
750
9.0
1.0
200
0.5
1.5
10
1000
0.150
0.200
1 Form A
5
6.5
500
3.75
0.4
12
15.0
1000
9.0
1.0
200
0.5
1.5
10
500
0.125
0.150
+/- 10%, 25° C
Must Operate by
Must Release by
Max DC/Peak AC Resist.
Max DC/Peak AC Resist.
Max DC/Peak AC Resist.
Max DC/Peak AC Resist.
Signal Level 1.0V, 1.0mA
50mV, 10mA
0.5V, 50mA
at 100 Hz, 1.5 msec
Between all Isolated Pins
at 100V, 25°C, 40% RH
No Shield
Shield Floating
Shield Guarding
No Shield
Shield Floating
Shield Guarding
Contacts Open, Shield
Floating
Between Contacts
Contacts to Shield
Contacts/Shield to Coil
At Nominal Coil Voltage,
30 Hz Square Wave
Zener-Diode Suppression
Diode Suppression
4
Ω
pF
pF
pF
pF
pF
pF
pF
VDC/peak AC
VDC/peak AC
VDC/peak AC
msec.
msec.
x
10
12
x
10
12
x
10
12
0.7
-
-
1.4
-
-
-
300
-
1500
0.35
0.10
-
-
0.8
0.1
-
1.4
0.5
1.4
300
1500
1500
0.35
0.10
-
0.1
-
-
2.0
-
-
-
200
-
1500
0.50
0.30
0.12
Top View:
Dot stamped
on relay refers
to pin #1
Grid = .1"x.1"
(2.54mm x 2.54mm)
Contact to Shield
Dielectric Strength
(minimum)
Operate Time - including
bounce - Typical
Release Time - Typical
Notes:
1
Consult factory for life expectancy at other switching
loads. 9090 series contact resistance >0.5W defines
end of life or failure to open.
2
Optional diode is connected to pin #2 (+) and pin #3(-).
Correct coil polarity must be observed.
3
9000 series part numbers designated with Form B
contacts, these relays contain bias magnets.
Correct coil polarity must be observed.
4
Consists of 20V Zener-diode and 1N1002 diode
in series, connected in parallel with coil.
Environmental Ratings
Storage Temp:-35°C to +100°C; Operating Temp:-20°C to +85°C
Solder Temp: 270°C max; 10 sec. max
The operate and release voltage and the coil resistance are
specified at 25°C. These values vary by approximately
0.4%/°C as the ambient temperature varies.
Vibration: 20 G’s to 2000 Hz; Shock: 50 G’s
COTO TECHNOLOGY
RHOPOINT COMPONENTS LTD
Holland Rd, Hurst Green, Oxted, Surrey, RH8 9AX,ENGLAND
RHOPOINT [ RHOPOINT COMPONENTS ]
