CRA04P
www.vishay.com
Vishay
TEST PROCEDURES AND REQUIREMENTS
IEC
REQUIREMENTS PERMISSIBLE
EN
60115-1
CLAUSE
60068-2
CHANGE (R) (1)
TEST
PROCEDURE
TEST
METHOD
STABILITY CLASS 2 OR BETTER
Stability for product type:
10 to 1 M
1 to 1 M
CRA04P
4.5
4.7
-
-
Resistance
-
2 ꢀ
5 ꢀ
Voltage proof
U = 1.4 x Uins; 60 s
U = 2.5 x P70 x R
2 × Umax.; Duration according to style
No flashover or breakdown
4.13
-
Short time overload
Solderability
(0.5 ꢀ R + 0.05 )
Good tinning ( 95 ꢀ covered)
Solder bath method; Sn60Pb40;
non-activated flux; (235 5) °C; (2 0.2) s
no visible damage
4.17.2
58 (Td)
-
Good tinning ( 95 ꢀ covered)
Solder bath method; Sn96.5Ag3Cu0.5;
non-activated flux; (245 5) °C; (3 0.3) s
no visible damage
4.8.4.2
4.32
Temperature coefficient
Shear (adhesion)
(20/- 55/20) °C and (20/125/20) °C
45 N
100 ppm/K
200 ppm/K
21 (UU3
)
No visible damage
No visible damage,
no open circuit in bent position
(0.25 ꢀ R + 0.05 )
4.33
4.19
21 (UU1
)
Substrate bending
Depth 2 mm; 3 times
30 min. at - 55 °C; 30 min at 125 °C
14 (Na)
Rapid change of temperature
5 cycles
1000 cycles
(0.5 ꢀ R + 0.05 )
(1 ꢀ R + 0.05 )
4.23
-
Dry heat
Damp heat, cyclic
Cold
-
4.23.2
4.23.3
4.23.4
4.23.5
4.23.6
4.23.7
2 (Ba)
30 (Db)
1 (Aa)
13 (M)
30 (Db)
-
125 °C; 16 h
55 °C; 90 ꢀ RH; 24 h; 1 cycle
- 55 °C; 2 h
Low air pressure
-
(2 ꢀ R + 0.05 )
1 kPa; (25 10) °C; 1 h
55 °C; 90 ꢀ RH; 24 h; 5 cycle
U = P70 x R
Damp heat, cyclic
D.C. load
U = P70 x R Umax.
1.5 h on; 0.5 h off;
70 °C; 1000 h
4.25.1
-
Endurance at 70 °C
(2 ꢀ R + 0.1 )
(4 ꢀ R + 0.1 )
70 °C; 8000 h
4.18.2
4.35
58 (Td)
-
Resistance to soldering heat
Flammability, needle flame test
Damp heat, steady state
Solder bath method; (260 5) °C; (10 1) s
IEC 60695-11-5; 10 s
(0.5 ꢀ R + 0.05 )
No burning after 30 s
(1 ꢀ R + 0.05 )
4.24
78 (Cab)
(40 2) °C; (93 3) ꢀ RH; 56 days
Endurance at
upper category temperature
4.25.3
-
155 °C; 1000 h
(2 ꢀ R + 0.1 )
Electrostatic discharge
(human body model)
IEC 61340-3-1; 3 positive and 3 negative
discharges; ESD voltage according to style
4.40
4.29
4.30
-
(1 ꢀ R + 0.05 )
45 (XA)
45 (XA)
Component solvent resistance
Isopropyl alcohol; 50 °C; method 2
No visible damage
Isopropyl alcohol; 50 °C; method 1;
toothbrush
Marking legible,
no visible damage
Solvent resistance of marking
f = 10 Hz to 2000 Hz; x, y, z 1.5 mm;
A 200 m/s2; 10 sweeps per axis
4.22
4.37
6 (Fc)
Vibration, endurance by sweeping
Periodic electric overload
(0.5 ꢀ R + 0.05 )
(1 ꢀ R + 0.05 )
(1 ꢀ R + 0.05 )
U = 15 x P70 x R 2 x Umax.
0.1 s on; 2.5 s off; 1000 cycles
-
-
Single pulse high voltage overload,
10 μs/700 μs
Û = 10 x P70 x R 2 x Umax.
4.27
10 pulses
Note
(1) Figures are given for a single element.
All tests are carried out in accordance with the following specifications:
• EN 60115-1, generic specification
• EN 140400, sectional specification
• EN 140401-802, detail specification
• IEC 60068-2, environmental test procedures
Packaging of components is done in paper or blister tapes according to IEC 60286-3.
Revision: 24-Jun-13
Document Number: 31048
3
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
QQ：528164397 复制
