EL2250CSZ应用文章市场行情现货热卖使用介绍供应商报价-中国IC网-芯三七

当前位置：IC37首页_>E字母起始型号索引_>E字母起始型号索引第411页更新时间：2025-02-18 13:40:11

产品型号EL2250CSZ的概述

芯片EL2250CSZ的概述 EL2250CSZ是一款高性能的视频放大器，组件通常用于各种视频处理和传输应用中。凭借其出色的带宽和低失真特性，EL2250CSZ被广泛应用于视频显示、视频监控及信号处理等多种电子设备中。该芯片通过简单的外部电路配置，可以实现多种功能，如增益调节和信号匹配。芯片EL2250CSZ的详细参数 EL2250CSZ的技术规格包括： 1. 增益：可选的增益范围通通常在2至10倍之间，具体根据外部电阻的配置而定。 2. 带宽：芯片的-3dB带宽可达到100MHz，适合处理高频信号。 3. 失真：在使用过程中，特别是在高频率输出时，EL2250CSZ表现出了非常低的总谐波失真（THD），最佳情况下可低至0.05%。 4. 电源电压：该芯片可在双电源模式下工作，电压范围为±5V至±15V，具有较好的灵活性。 5. 工作温度：工作温度范围为-40°C到+85°C，适合在...

产品型号EL2250CSZ的Datasheet PDF文件预览

EL2250, EL2450

Data Sheet

June 7, 2005

FN7061.2

125MHz Single Supply Dual/Quad Op

Amps

Features

• Specified for +3V, +5V, or ±5V applications

The EL2250/EL2450 are part of a family of the electronics

industries fastest single supply op amps available. Prior

single supply op amps have generally been limited to

bandwidths and slew rates to that of the EL2250/EL2450.

The 125MHz bandwidth, 275V/µs slew rate, and

• Large input common mode range

0V < V

< V -1.2V

• Output swings to ground without saturating

• -3dB bandwidth = 125MHz

0.05%/0.05° differential gain/differential phase makes this

part ideal for single or dual supply video speed applications.

With its voltage feedback architecture, this amplifier can

accept reactive feedback networks, allowing them to be

used in analog filtering applications. The inputs can sense

signals below the bottom supply rail and as high as 1.2V

below the top rail. Connecting the load resistor to ground

and operating from a single supply, the outputs swing

completely to ground without saturating. The outputs can

also drive to within 1.2V of the top rail. The EL2250/EL2450

will output ±100mA and will operate with single supply

voltages as low as 2.7V, making them ideal for portable, low

power applications.

• ±0.1dB bandwidth = 30MHz

• Low supply current = 5mA (per amplifier)

• Slew rate = 275V/µs

• Low offset voltage = 4mV max

• Output current = ±100mA

• High open loop gain = 80dB

• Differential gain = 0.05%

• Differential phase = 0.05°

• Pb-free plus anneal available (RoHS compliant)

The EL2250/EL2450 are available in PDIP and SO

packages in industry standard pin outs. Both parts operate

over the industrial temperature range of -40°C to +85°C, and

are part of a family of single supply op amps. For single

amplifier applications, see the EL2150/EL2157. For dual and

triple amplifiers with power down and output voltage clamps,

see the EL2257/EL2357.

Applications

• Video amplifiers

• PCMCIA applications

• A/D drivers

• Line drivers

• Portable computers

• High speed communications

• RGB printers, FAX, scanners

• Broadcast equipment

• Active filtering

Ordering Information

TAPE &

PART NUMBER

EL2250CN

EL2250CS

EL2250CS-T7

EL2250CS-T13

PACKAGE

8-Pin PDIP

8-Pin SO

REEL

PKG. DWG. #

MDP0031

MDP0027

7”

13”

EL2250CSZ

(See Note)

8-Pin SO

(Pb-free)

EL2250CSZ-T7

(See Note)

EL2250CSZ-T13

(See Note)

8-Pin SO

(Pb-free)

8-Pin SO

(Pb-free)

7”

MDP0027

13”

EL2450CN

EL2450CS

EL2450CS-T7

EL2450CS-T13

14-Pin PDIP

14-Pin SO

MDP0031

MDP0027

7”

13”

NOTE: Intersil Pb-free plus anneal products employ special Pb-free

material sets; molding compounds/die attach materials and 100%

matte tin plate termination finish, which are RoHS compliant and

compatible with both SnPb and Pb-free soldering operations. Intersil

Pb-free products are MSL classified at Pb-free peak reflow

temperatures that meet or exceed the Pb-free requirements of

IPC/JEDEC J STD-020.

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.

All other trademarks mentioned are the property of their respective owners.

EL2250, EL2450

Pinouts

EL2250C

(8-PIN SO, PDIP)

TOP VIEW

EL2450

(14-PIN SO, PDIP)

TOP VIEW

OUTA

INA-

VS+

OUTA

INA-

OUTD

IND-

OUTB

INB-

INA+

GND

INA+

VS+

IND+

GND

INC+

INC-

INB+

INB-

OUTB

OUTC

FN7061.2

June 7, 2005

EL2250, EL2450

Absolute Maximum Ratings (T = 25°C)

Supply Voltage between V and GND. . . . . . . . . . . . . . . . . . +12.6V

Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves

Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C

Ambient Operating Temperature Range . . . . . . . . . .-40°C to +85°C

Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150°C

Input Voltage (IN+, IN-) . . . . . . . . . . . . . . . . . . . GND-0.3V,V +0.3V

Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±6V

Maximum Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90mA

Output Short Circuit Duration. . . . . . . . . . . . . . . . . . . . . . . . (Note 1)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests

are at the specified temperature and are pulsed tests, therefore: T = T = T

DC Electrical Specifications

= +5V, GND = 0V, T = 25°C, V

= 1.5V, V = 1.5V, unless otherwise specified.

OUT

TEST CONDITIONS

PARAMETER

DESCRIPTION

MIN

-2

TYP

MAX

UNIT

µV/°C

µA

Offset Voltage

EL2250

EL2450

-4

TCV

Offset Voltage Temperature Coefficient

Input Bias Current

Measured from T

to T

-5.5

150

MIN

MAX

= 0V

-10

Input Offset Current

-750

750

TCI

Input Bias Current Temperature Coefficient Measured from T

nA/°C

MIN

PSRR

CMRR

Power Supply Rejection Ratio

Common Mode Rejection Ratio

= +2.7V to +12V

VCM = 0V to +3.8V

VCM = 0V to +3.0V

CMIR

Common Mode Input Range

Input Resistance

V -1.2

Common Mode

SO Package

MΩ

Input Capacitance

PDIP Package

1.5

Output Resistance

= +1

mΩ

OUT

Supply Current (per amplifier)

Power Supply Operating Range

= +12V

6.5

PSOR

2.7

12.0

DC Electrical Specifications

= +5V, GND = 0V, T = 25°C, V

= +1.5V, V

= +1.5V, unless otherwise specified.

OUT

PARAMETER

DESCRIPTION

Open Loop Gain

TEST CONDITIONS

MIN

TYP

MAX

UNIT

AVOL

= +12V, V

= +2V to +9V, R = 1kΩ to GND

OUT

= +1.5V to +3.5V, R = 1kΩ to GND

OUT

= +1.5V to +3.5V, R = 150Ω to GND

Positive Output

Voltage Swing

= +12V, A = +1, R = 1kΩ to 0V

10.8

10.0

4.0

= +12V, A = +1, R = 150Ω to 0V

9.6

= ±5V, A = +1, R = 1kΩ to 0V

= ±5V, A = +1, R = 150Ω to 0V

3.4

1.8

3.8

= +3V, A = +1, R = 150Ω to 0V

1.95

5.5

Negative Output

Voltage Swing

= +12V, A = +1, R = 150Ω to 0V

= ±5V, A = +1, R = 1kΩ to 0V

-4.0

-3.7

±100

= ±5V, A = +1, R = 150Ω to 0V

-3.4

Output Current (Note 1)

= ±5V, A = +1, R = 10Ω to 0V

±75

OUT

= ±5V, A = +1, R = 50Ω to 0V±60VmA

NOTE:

1. Internal short circuit protection circuitry has been built into the EL2250/EL2450; see the Applications section

FN7061.2

June 7, 2005

EL2250, EL2450

AC Electrical Specifications

= +5V, GND = 0V, T = 25°C, V

= +1.5V, V

= +1.5V, A = +1, R = 0Ω, R = 150Ω to GND pin,

OUT V F L

unless otherwise specified. (Note 1)

TEST CONDITIONS

PARAMETER

DESCRIPTION

MIN

TYP

125

MAX

UNIT

MHz

-3dB Bandwidth

OUT

= +5V, A = +1, R = 0Ω

(V =400mV

)

P-P

= +5V, A = -1, R = 500Ω

= +5V, A = +2, R = 500Ω

= +5V, A = +10, R = 500Ω

= +12V, A = +1, R = 0Ω

150

100

= +3V, A = +1, R = 0Ω

±0.1dB Bandwidth

(V =400mV

= +12V, A = +1, R = 0Ω

V F

)

OUT

P-P

= +5V, A = +1, R = 0Ω

= +3V, A = +1, R = 0Ω

GBWP

Gain Bandwidth Product

Phase Margin

= +12V, @ A = +10

R = 1kΩ, C = 6pF

Slew Rate

= +10V, R = 150Ω, V

= 0V to +6V

200

275

300

2.8

V/µs

OUT

= 0V to +3V

OUT

= +5V, R = 150Ω, V

t , t

Rise Time, Fall Time

Overshoot

±0.1V Step

Propagation Delay

0.1% Settling Time

0.01% Settling Time

Differential Gain (Note 2)

Differential Phase (Note 2)

Input Noise Voltage

Input Noise Current

3.2

= ±5V, R = 500Ω, A = +1, V

= ±3V

OUT

= ±5V, R = 500Ω, A = +1, V

= +2, R = 1kΩ

0.05

= +2, R = 1kΩ

f = 10kHz

nV/√Hz

pA/√Hz

1.25

NOTES:

1. All AC tests are performed on a “warmed up” part, except slew rate, which is pulse tested

2. Standard NTSC signal = 286mV , f = 3.58MHz, as V is swept from 0.6V to 1.314V; R is DC coupled

P-P IN

FN7061.2

June 7, 2005

EL2250, EL2450

Typical Performance Curves

Non-Inverting Frequency

Response (Gain)

Non-Inverting Frequency

Response (Phase)

3dB Bandwidth vs Temperature for

Non-Inverting Gains

Inverting Frequency Response

(Gain)

Inverting Frequency Response

(Phase)

3dB Bandwidth vs Temperature for

Inverting Gains

Non-Inverting Frequency

Response vs Common Mode

Voltage

Frequency Response for Various R

Frequency Response for Various C

FN7061.2

June 7, 2005

EL2250, EL2450

Typical Performance Curves (Continued)

3dB Bandwidth vs Supply Voltage

for Non-Inverting Gains

Frequency Response for Various

PSSR and CMRR vs Frequency

Supply Voltages, A = + 1

3dB Bandwidth vs Supply Voltage

for Inverting Gains

Frequency Response for Various

PSRR and CMRR vs Die

Temperature

Supply Voltages, A = + 2

Open Loop Gain and Phase vs

Frequency

Open Loop Voltage Gain vs Die

Temperature

Closed Loop Output Impedance vs

Frequency

FN7061.2

June 7, 2005

EL2250, EL2450

Typical Performance Curves (Continued)

Large Signal Step Response, V = +3V

Large Signal Step Response, V = +5V

Large Signal Step Response, V = +12V

Small Signal Step Response

Large Signal Step Response, V = ±5V

Slew Rate vs Temperature

Settling Time vs Settling Accuracy

Voltage and Current Noise vs

Frequency

FN7061.2

June 7, 2005

EL2250, EL2450

Typical Performance Curves (Continued)

Differential Gain for

Single Supply Operation

Differential Phase for

Single Supply Operation

Differential Gain and Phase

for Dual Supply Operation

2nd and 3rd Harmonic Distortion

vs Frequency

2nd and 3rd Harmonic Distortion

vs Frequency

2nd and 3rd Harmonic Distortion

vs Frequency

Output Voltage Swing vs

Frequency for THD < 0.1%

Output Voltage Swing vs

Frequency for Unlimited Distortion

Output Current vs Die

Temperature

FN7061.2

June 7, 2005

EL2250, EL2450

Typical Performance Curves (Continued)

Supply Current vs Supply Voltage

(per amplifier)

Input Resistance vs Die

Temperature

Supply Current vs Die

Temperature (per amplifier)

Input Offset Current and Input Bias

Current vs Die Temperature

Offset Voltage vs Die Temperature

(4 Samples)

Input Bias Current vs Input

Voltage

Positive Output Voltage Swing vs

Negative Output Voltage Swing vs

Channel to Channel Isolation vs

Frequency

Die Temperature, R = 150Ω to

GND

Package Power Dissipation vs Ambient Temp.

JEDEC JESD51-3 Low Effective Thermal Conductivity

Test Board

Package Power Dissipation vs Ambient Temp.

SEMI G42-88 Single Layer Test Board

1.8

1.2

1.042W

1.54W

1.25W

1.6

1.4

1.2

781W

0.8

0.6

0.4

0.2

0.8

0.6

0.4

0.2

75 85 100

125

150

75 85 100

125

150

Ambient Temperature (°C)

FN7061.2

June 7, 2005

EL2250, EL2450

Simplified Schematic

used. Carbon or Metal-Film resistors are acceptable with the

Applications Information

Product Description

Metal-Film resistors giving slightly less peaking and

bandwidth because of their additional series inductance. Use

of sockets, particularly for the SO package should be

avoided if possible. Sockets add parasitic inductance and

capacitance which will result in some additional peaking and

overshoot.

The EL2250/EL2450 are part of a family of the industries

fastest single supply operational amplifiers. Connected in

voltage follower mode, their -3dB bandwidth is 125MHz

while maintaining a 275V/µs slew rate. With an input and

output common mode range that includes ground, these

amplifiers were optimized for single supply operation, but will

also accept dual supplies. They operate on a total supply

voltage range as low as +2.7V or up to +12V. This makes

them ideal for +3V applications, especially portable

computers.

Supply Voltage Range and Single-Supply

Operation

The EL2250/EL2450 have been designed to operate with

supply voltages having a span of greater than 2.7V, and less

than 12V. In practical terms, this means that the

EL2250/EL2450 will operate on dual supplies ranging from

±1.35V to ±6V. With a single-supply, the EL2250/EL2450 will

operate from +2.7V to +12V. Performance has been

optimized for a single +5V supply.

While many amplifiers claim to operate on a single supply,

and some can sense ground at their inputs, most fail to truly

drive their outputs to ground. If they do succeed in driving to

ground, the amplifier often saturates, causing distortion and

recovery delays. However, special circuitry built into the

EL2250/EL2450 allows the output to follow the input signal

to ground without recovery delays.

Pins 8 and 4 are the power supply pins on the EL2250. The

positive power supply is connected to pin 8. When used in

single supply mode, pin 4 is connected to ground. When

used in dual supply mode, the negative power supply is

connected to pin 4.

Power Supply Bypassing And Printed Circuit

Board Layout

Pins 4 and 11 are the power supply pins on the EL2450. The

positive power supply is connected to pin 4. When used in

single supply mode, pin 11 is connected to ground. When

used in dual supply mode, the negative power supply is

connected to pin 11.

As with any high-frequency device, good printed circuit

board layout is necessary for optimum performance. Ground

plane construction is highly recommended. Lead lengths

should be as short as possible. The power supply pins must

be well bypassed to reduce the risk of oscillation. The

combination of a 4.7µF tantalum capacitor in parallel with a

0.1µF ceramic capacitor has been shown to work well when

placed at each supply pin. For single supply operation,

where the GND pin is connected to the ground plane, a

single 4.7µF tantalum capacitor in parallel with a 0.1µF

As supply voltages continue to decrease, it becomes

necessary to provide input and output voltage ranges that

can get as close as possible to the supply voltages. The

EL2250/EL2450 have an input voltage range that includes

the negative supply and extends to within 1.2V of the

positive supply. So, for example, on a single +5V supply, the

EL2250/EL2450 have an input range which spans from 0V to

3.8V.

ceramic capacitor across the V + and GND pins will suffice.

For good AC performance, parasitic capacitance should be

kept to a minimum. Ground plane construction should be

FN7061.2

June 7, 2005

EL2250, EL2450

The output range of the EL2250/EL2450 is also quite large.

value. While driving a light load, such as 1kΩ, if the input

black level is kept above 1.25V, dG and dP are a respectable

0.03% and 0.03°.

It includes the negative rail, and extends to within 1V of the

top supply rail with a 1kΩ load. On a +5V supply, the output

is therefore capable of swinging from 0V to +4V. On split

supplies, the output will swing ±4V. If the load resistor is tied

to the negative rail and split supplies are used, the output

range is extended to the negative rail.

For other biasing conditions see the Differential Gain and

Differential Phase vs. Input Voltage curves.

Output Drive Capability

In spite of their moderately low 5mA of supply current, the

EL2250/EL2450 are capable of providing ±100mA of output

current into a 10Ω load, or ±60mA into 50Ω. With this large

output current capability, a 50Ω load can be driven to ±3V

Choice Of Feedback Resistor, R

The feedback resistor forms a pole with the input

capacitance. As this pole becomes larger, phase margin is

reduced. This increases ringing in the time domain and

with V = ±5V, making it an excellent choice for driving

peaking in the frequency domain. Therefore, R has some

isolation transformers in telecommunications applications.

maximum value which should not be exceeded for optimum

performance. If a large value of R must be used, a small

Driving Cables and Capacitive Loads

capacitor in the few picofarad range in parallel with R can

When used as a cable driver, double termination is always

recommended for reflection-free performance. For those

applications, the back-termination series resistor will de-

couple the EL2250/EL2450 from the cable and allow

extensive capacitive drive. However, other applications may

have high capacitive loads without a back-termination

resistor. In these applications, a small series resistor (usually

between 5Ω and 50Ω) can be placed in series with the

help to reduce this ringing and peaking at the expense of

reducing the bandwidth.

As far as the output stage of the amplifier is concerned,

R + R appear in parallel with R for gains other than +1.

As this combination gets smaller, the bandwidth falls off.

Consequently, R has a minimum value that should not be

exceeded for optimum performance.

output to eliminate most peaking. The gain resistor (R ) can

For A = +1, R = 0Ω is optimum. For A = -1 or +2 (noise

then be chosen to make up for any gain loss which may be

created by this additional resistor at the output.

gain of 2), optimum response is obtained with R between

500Ω and 1kΩ. For Av = -4 or +5 (noise gain of 5), keep R

between 2kΩ and 10kΩ.

Video Sync Pulse Remover Application

All CMOS Analog to Digital Converters (A/Ds) have a

parasitic latch-up problem when subjected to negative input

voltage levels. Since the sync tip contains no useful video

information and it is a negative going pulse, we can chop it

off.

Video Performance

For good video performance, an amplifier is required to

maintain the same output impedance and the same

frequency response as DC levels are changed at the output.

This can be difficult when driving a standard video load of

150Ω, because of the change in output current with DC level.

Differential Gain and Differential Phase for the

Figure 1 shows a unity gain connected amplifier A of an

EL2250. Figure 2 shows the complete input video signal

applied at the input, as well as the output signal with the

negative going sync pulse removed.

EL2250/EL2450 are specified with the black level of the

output video signal set to +1.2V. This allows ample room for

the sync pulse even in a gain of +2 configuration. This

results in dG and dP specifications of 0.05% and 0.05° while

driving 150Ω at a gain of +2. Setting the black level to other

values, although acceptable, will compromise peak

performance. For example, looking at the single supply dG

and dP curves for R =150Ω, if the output black level clamp is

reduced from 1.2V to 0.6V dG/dP will increase from

0.05%/0.05° to 0.08%/0.25° Note that in a gain of +2

configuration, this is the lowest black level allowed such that

the sync tip doesn’t go below 0V.

If your application requires that the output goes to ground,

then the output stage of the EL2250/EL2450, like all other

single supply op amps, requires an external pull down

resistor tied to ground. As mentioned above, the current

flowing through this resistor becomes the DC bias current for

the output stage NPN transistor. As this current approaches

zero, the NPN turns off, and dG and dP will increase. This

becomes more critical as the load resistor is increased in

FIGURE 1.

FN7061.2

June 7, 2005

EL2250, EL2450

The maximum power dissipation allowed in a package is

determined according to [1]:

– T

JMAX

AMAX

--------------------------------------------

MAX

FIGURE 2.

where:

= Maximum Junction Temperature

= Maximum Ambient Temperature

JMAX

Short Circuit Current Limit

AMAX

The EL2250/EL2450 have internal short circuit protection

circuitry that protect it in the event of its output being shorted

to either supply rail. This limit is set to around 100mA

nominally and reduces with increasing junction temperature.

It is intended to handle temporary shorts. If an output is

shorted indefinitely, the power dissipation could easily

increase such that the part will be destroyed. Maximum

reliability is maintained if the output current never exceeds

±90mA. A heat sink may be required to keep the junction

temperature below absolute maximum when an output is

shorted indefinitely.

= Thermal Resistance of the Package

= Maximum Power Dissipation in the Package.

MAX

The maximum power dissipation actually produced by an IC

is the total quiescent supply current times the total power

supply voltage, plus the power in the IC due to the load, or

[2]:









OUT

---------------

= N × V × I

+ (V – V

OUT

) ×



MAX

SMAX



where:

Power Dissipation

With the high output drive capability of the EL2250/EL2450,

it is possible to exceed the 150°C Absolute Maximum

junction temperature under certain load current conditions.

Therefore, it is important to calculate the maximum junction

temperature for the application to determine if power-supply

voltages, load conditions, or package type need to be

modified for the EL2250/EL2450 to remain in the safe

operating area.

N = Number of amplifiers

V = Total Supply Voltage

= Maximum Supply Current per amplifier

SMAX

= Maximum Output Voltage of the Application

OUT

R = Load Resistance tied to Ground

If we set the two PD

MAX

equations, [1] & [2], equal to each

other, and solve for V , we can get a family of curves for

various loads and output voltages according to [3]:

× (T

– T

AMAX

)

JMAX

---------------------------------------------------------------

+ (V

)

OUT

N × θ

------------------------------------------------------------------------------------------

(IS × R ) + V

OUT

Figures 3 through 6 below show total single supply voltage

V vs. R for various output voltage swings for the PDIP and

SO packages. The curves assume WORST CASE

conditions of T = +85°C and I = 6.5mA per amplifier.

FN7061.2

June 7, 2005

EL2250, EL2450

EL2450 Single Supply Voltage vs

for Various V (PDIP

EL2250 Single Supply Voltage vs

for Various V (PDIP

LOAD

Package)

OUT

LOAD

Package)

OUT

FIGURE 3.

FIGURE 5.

EL2450 Single Supply Voltage vs

for Various V (SO

EL2250 Single Supply Voltage vs

for Various V (SO

LOAD

Package)

OUT

LOAD

Package)

OUT

FIGURE 4.

FIGURE 6.

FN7061.2

June 7, 2005

EL2250, EL2450

EL2250/EL2450 Macromodel (one amplifier)

* Revision A, April 1996

* Pin numbers reflect a standard single op amp.

* Connections:

+input

-input

+Vsupply

-Vsupply

output

.subckt EL2250/el 3

* Input Stage

i1 7 10 250µA

i2 7 11 250µA

r1 10 11 4k

q1 12 2 10 qp

q2 13 3 11 qpa

r2 12 4 100

r3 13 4 100

* Second Stage & Compensation

gm 15 4 13 12 4.6m

r4 15 4 15Meg

c1 15 4 0.36pF

* Poles

e1 17 4 15 4 1.0

r6 17 25 400

c3 25 4 1pF

r7 25 18 500

c4 18 4 1pF

* Output Stage

i3 20 4 1.0mA

q3 7 23 20 qn

q4 7 18 19 qn

q5 7 18 21 qn

q6 4 20 22 qp

q7 7 23 18 qn

d1 19 20 da

r8 21 6 2

r9 22 6 2

r10 18 21 10k

r11 7 23 100k

d2 23 24 da

d3 24 4 da

d4 23 18 da

* Power Supply Current

ips 7 4 3.2mA

* Models

.model qn npn(is=800e-18 bf=150 tf=0.02nS)

.model qpa pnp(is=810e-18 bf=50 tf=0.02nS)

.model qp pnp(is=800e-18 bf=54 tf=0.02nS)

.model da d(tt=0nS)

.ends

FN7061.2

June 7, 2005

EL2250, EL2450

EL2250/EL2450 Macromodel (one amplifier)

All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.

Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality

Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without

notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and

reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result

from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.

For information regarding Intersil Corporation and its products, see www.intersil.com

FN7061.2

June 7, 2005

EL2250CSZ相关文章

配单直通车

深圳市中利达电子科技有限公司服务专线: 0755-13686833545 在线联系:

QQ：1902134819 复制

QQ：2881689472 复制

柒号芯城电子商务（深圳）有限公司服务专线: 18922803401 在线联系:

QQ：2881677436 复制

QQ：2881620402 复制

首天国际（深圳）科技有限公司服务专线: 0755-82807802/82807803 在线联系:

QQ：528164397 复制

QQ：1318502189 复制

深圳市芯福林电子有限公司服务专线: 13418564337 在线联系:

QQ：2881495808 复制

QQ：308365177 复制

北京元坤伟业科技有限公司服务专线: 010-62104931621064316210489162104791 在线联系:

QQ：857273081 复制

QQ：1594462451 复制

EL2250CSZ产品参数

型号:	EL2250CSZ
Brand Name：	Intersil
是否Rohs认证：	符合
生命周期：	Obsolete
IHS 制造商：	INTERSIL CORP
零件包装代码：	SOIC
包装说明：	SOP-8
针数：	8
Reach Compliance Code：	compliant
ECCN代码：	EAR99
HTS代码：	8542.33.00.01
Factory Lead Time：	1 week
风险等级：	5.73
Is Samacsys：	N
放大器类型：	OPERATIONAL AMPLIFIER
JESD-30 代码：	R-PDSO-G8
JESD-609代码：	e3
长度：	4.89 mm
湿度敏感等级：	3
功能数量：	2
端子数量：	8
封装主体材料：	PLASTIC/EPOXY
封装代码：	SOP
封装形状：	RECTANGULAR
封装形式：	SMALL OUTLINE
峰值回流温度（摄氏度）：	260
认证状态：	Not Qualified
座面最大高度：	1.68 mm
子类别：	Operational Amplifier
表面贴装：	YES
温度等级：	INDUSTRIAL
端子面层：	Matte Tin (Sn) - annealed
端子形式：	GULL WING
端子节距：	1.27 mm
端子位置：	DUAL
处于峰值回流温度下的最长时间：	40
宽度：	3.9 mm
Base Number Matches：	1

电子百科

产品导航

产品型号EL2250CSZ的概述

产品型号EL2250CSZ的Datasheet PDF文件预览

EL2250CSZ相关产品..

EL2250CSZ相关文章

IC37:专业IC行业平台