H101C供应商报价哪里找芯片批发报价原理和应用中文资料-中国IC网-芯三七

产品型号H101E的Datasheet PDF文件预览

H100E _Series

Low Cost, 1W,

Ultra-Miniature

DC/DC Converters

Electrical Speciﬁcations

Speciﬁcations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Speciﬁcations subject to change without notice.

Key Features:

• 1W Output Power

Input

Parameter

Conditions

3.3 VDC Input

5 VDC Input

Min.

3.0

Typ.

3.3

Max.

3.6

Units

• Miniature MiniDIP Case

• UL Approved (File E245422)

• 1,000 VDC Isolation

• >3.5 MHour MTBF

4.5

5.0

5.5

Input Voltage Range

VDC

12 VDC Input 10.8

24 VDC Input 21.6

Internal Capacitor

12.0

24.0

13.2

26.4

Input Filter

Reverse Polarity Input Current

0.3

• 17 Standard Models

• Industry Standard Pin-Out

• LOWEST COST!

Output

Parameter

Output Voltage Accuracy

Line Regulation, 3.3V Output Models

Line Regulation, All Other Models

Load Regulation

Conditions

Min.

Typ.

Max.

3.0

Units

1.0

1.5

For Vin Change of 1%

1.2

See Model Selection Guide

Ripple & Noise (20 MHz)

Output Power Protection

Temperature Coefﬁcient

Output Short Circuit

General

100

mV P - P

120

0.03

%/ºC

Momentary (1.0 Sec.)

Parameter

Conditions

Min.

60 Seconds 1,000

500 VDC 1,000

100 kHz, 1V

Typ.

Max.

Units

VDC

MΩ

Isolation Voltage

Isolation Resistance

Isolation Capacitance

Switching Frequency

Environmental

100

kHz

Parameter

Min.

Typ.

Max.

+85

Units

ºC

Operating Temperature Range

Storage Temperature Range

Cooling

Ambient

-40

-55

+25

+125

ºC

Free Air Convection

RH, Non-condensing

Humidity

Physical

Case Size, Single Output Models

0.50 x 0.393 x 0.30 Inches (12.70 x 10.00 x 7.70 mm)

Non-Conductive Black Plastic (UL94-V0)

0.06 Oz (1.8g)

MicroPower Direct

292 Page Street

Suite D

Stoughton, MA 02072

USA

Case Material

Weight

Reliability Speciﬁcations

Parameter

Conditions

Min.

Typ.

Max.

Units

MTBF

MIL HDBK 217F, 25ºC, Gnd Benign

3.5

MHours

T: (781) 344-8226

F: (781) 344-8481

E: sales@micropowerdirect.com

W: www.micropowerdirect.com

Safety Standards

UL 1950, EN 60950, IEC 60950

UL, cUL; File No. E245422

Safety Approvals

Not 3.3 Vout Models

Absolute Maximum Ratings

Parameter

Conditions

Min.

Typ.

Max.

7.0

Units

3.3 VDC Input -0.7

5 VDC Input -0.7

12 VDC Input -0.7

24 VDC Input -0.7

9.0

Input Voltage Surge (1 Sec)

VDC

18.0

30.0

300

450

Lead Temperature

1.5 mm From Case For 10 Sec

All Models

ºC

Internal Power Dissipation

Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.

Model Selection Guide

Input

Output

Current

(mA, Max)

303.0

200.0

111.0

83.0

Load

Regulation

(%, Max)

Fuse Rating

Slow-Blow

(mA)

500

Model

Number

Efﬁciency

(%, Typ)

Voltage (VDC)

Nominal Range

Current (mA)

Voltage

(VDC)

3.3

Current

(mA, Min)

30.0

20.0

12.0

9.5

Full-Load

No-Load

H101E

H102E

H103E

H104E

H105E

H111E

H112E

H113E

H114E

H115E

H121E

H122E

H123E

H124E

H125E

H151E

H152E

3.3

4.5 - 5.5

10.8 - 13.2

21.6 - 26.4

3.0 - 3.6

278

286

256

252

251

116

118

109

106

105

5.0

9.0

12.0

15.0

3.3

5.0

9.0

12.0

15.0

3.3

5.0

9.0

12.0

15.0

3.3

500

200

100

750

67.0

7.0

303.0

200.0

111.0

83.0

30.0

20.0

12.0

9.0

67.0

7.0

303.0

200.0

111.0

83.0

67.0

303.0

200.0

30.0

20.0

12.0

9.0

7.0

30.0

20.0

421

410

3.0 - 3.6

5.0

Notes:

1. Output load regulation is speciﬁed for a load change of 10% to 100%.

2. When measuring output ripple, it is recommended that an external 0.33 µF

ceramic capacitor be placed from the +Vout pin to the -Vout pin.

3. During operation, care must be taken not to exceed the speciﬁed input range

of the unit or to allow the output load to drop below the speciﬁed minimum

(10% of full load). Operating the unit under either of these conditions could

cause damage to the unit.

Derating Curve

4. These converters are speciﬁed for operation without external components.

However, in some applications the addition of input/output capacitors will

enhance stability and reduce output ripple. Recommended capacitor values

are:

Input

Capacitor

4.7 µF

2.2 µF

Output

Capacitor

10.0 µF

4.7 µF

2.2 µF

1.0 µF

Vin

Vout

3.3 VDC

5 VDC

12 VDC

24 VDC

3.3 VDC

5 VDC

9 VDC

12 VDC

15 VDC

1.0 µF

For applications requiring very low output noise levels, a

simple LC ﬁlter should be effective.

5. It is recommended that a fuse be used on the input of a power

supply for protection. See the table above for the correct rating.

Mechanical Dimensions

Pin Connections

Function

-Vin

+Vin

+Vout

-Vout

Notes:

• All dimensions are typical in inches (mm)

• Tolerance x.xx = 0.01 ( 0.25)

• Pin 1 is marked by a “dot” or indentation on the

top of the unit

MicroPower Direct

•

www.micropowerdirect.com

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

型号:	H101CBC
是否Rohs认证：	符合
生命周期：	Contact Manufacturer
Reach Compliance Code：	compliant
HTS代码：	8541.40.20.00
风险等级：	4.78
颜色@波长：	Green/Orange-Red
JESD-609代码：	e2
光电设备类型：	LED MOUNTING HARDWARE
总高度：	7.1 mm
子类别：	Visible LEDs
端子面层：	Tin/Copper (Sn/Cu)
Base Number Matches：	1

电子百科

产品导航

产品型号H101E的Datasheet PDF文件预览

H101C相关产品..

H101C相关文章

IC37:专业IC行业平台